Jump to content

Everything 800mhz (1xA, LTE, coverage, timeline, etc)


Recommended Posts

Forgive me if this has been covered but I have an interesting find in KC. Now that we are seeing all 3 bands pretty well I have noticed that when my phone goes to band 26 the 1x band camps on Secondary 800 no matter what but when LTE is on 25 or 41 the 1x band is on PCS. It would appear that there is a tie between the two. Even when 1900 voice has great signal as long as LTE is on band 26 it will only use band 10 for voice.

Edited by sporter82
Link to comment
Share on other sites

Surprisingly enough, 800 sites are all over the country in big cities and the boondocks alike.

 

Until I cough up the dough I'm gonna have to take a drive! Fortunately what I consider the start of the boonies (the cell companies do too) is only 10 miles from here. I'll probably be in the city sooner though, and can't wait to see if I pick up anything! I'll be jumping for joy if I pick up LTE inside the building where my mothers shop is located. The place was a black hole even for 1x up until maybe midway through last year. 

Link to comment
Share on other sites

Forgive me if this has been covered but I have an interesting find in KC. Now that we are seeing all 3 bands pretty well I have noticed that when my phone goes to band 26 the 1x band camps on Secondary 800 no matter what but when LTE is on 25 or 41 the 1x band is on PCS. It would appear that there is a tie between the two. Even when 1900 voice has great signal as long as LTE is on band 26 it will only use band 10 for voice.

 

Which makes sense though, since the coverage would have a similar range.

 

What phone do you have? The G2?

Link to comment
Share on other sites

Just picked up LTE 800 26 miles north of Lafayette, IN heading southbound on I65!

I was just about ready to lose hope because I had nothing but 3G or 1x until just a few minutes ago. ImageUploadedByTapatalk1396641772.034196.jpgimage.jpg

  • Like 3
Link to comment
Share on other sites

will Lte 800 work better in apt complex I barely get 4g lte inside my apt and it keeps switching back and fourth with 800 voice

Band 26 is a lower frequency. Therefore, it propagates better. It travels further, and is generally unburdened. Think of it as a whole separate network that has (at the moment) really nobody on it. So yes, you should see an improvement in your apartment.

 

Sent from my Nexus 5 using Tapatalk

 

 

Link to comment
Share on other sites

so I took the plunge and upgraded to a premier sponsor so I could ogle the band 26 sites and noticed that my area is filled with the dreaded brown tdb dots. I have chatting online with sprint, tweeted sprint, talked to store employees and the reps when they were there and they all said LTE 800 within 3 months. How accurate have the time tables been on the Band 26 map?  

Link to comment
Share on other sites

Is there any reason why my phone would just keep using 1X 800 all the time? I was driving back and once my phone picked it up it didn't let go. Got into my hometown and it still sticks to 1X 800, I never had signal problems before in any of the areas

 

Sent from my SPH-L710 using Tapatalk

 

 

Link to comment
Share on other sites

Is there any reason why my phone would just keep using 1X 800 all the time? I was driving back and once my phone picked it up it didn't let go. Got into my hometown and it still sticks to 1X 800, I never had signal problems before in any of the areas

 

Sent from my SPH-L710 using Tapatalk

Yep, that is what it does.  Someplace you hit a spot where 1900 dropped and when that happens, you quite often pick up 800.  It is supposed to work that way.  When you do get on 800, it normally tends to stay there and this is fine. You may or may not drop off of the 800 and go back to 1900.  Sprint can probably push you off the 800 anytime they want.  If 800 is not swamped with users, you may just stay there for awhile.

  • Like 1
Link to comment
Share on other sites

Is there any reason why my phone would just keep using 1X 800 all the time? I was driving back and once my phone picked it up it didn't let go. Got into my hometown and it still sticks to 1X 800, I never had signal problems before in any of the areas

Because your device won't re-scan for other CDMA 1X bands until it loses the one it is connected to. There is no concern with remaining on 800 (SMR) vs. 1900 (PCS), or never connecting to one or the other.

 

800 MHz provides better signal propagation, but that doesn't mean that you need to camp on it 24/7 when your phone has determined that PCS is strong enough at your location. If it wasn't for engineering screens or apps like SignalCheck, you wouldn't be able to tell the difference.

 

-Mike

  • Like 3
Link to comment
Share on other sites

Well today I got to experience what 1x800 is like when your in a rural area and cell sites are lacking, I already have experienced how wonderful it is for inside dense buildings.

 

I traveled from Bloomington, IN east to Nashville, IN in Brown County. Between there and Bloomington there are no sites. What was awesome is that I was connected to 1x800 almost the whole way there instead of roaming on VZW like I would've if it were still PCS only. The terrain is very hilly so signal gets blocked easily, I did eventually switch to no service a few miles before town and finally had to enable roaming, but considering that from Bloomington to Nashville is 16 miles through hilly terrain with no Sprint sites in between, that was great! Now if they'd just get LTE800 enabled quicker that would be better! I'm starting to tire of all these LTE dead spots I discover all over the place in towns.

 

After that I traveled to Lake Lemon, a place tucked even deeper away in the hills and I was still picking up 1x800 but it faded a lot, finally had to let my phone roam instead.

 

One thing I observed and would like confirmation, is the latest iPhone PRL now allowing 1x800 over roaming? I know a year ago SMR was way last.

  • Like 2
Link to comment
Share on other sites

Does anyone know if there's enough 800mhz spectrum in bta 52 for a 5×5mhz of lte to be deployed there I've looked at the spectrum maps but I am kind of confused.

Link to comment
Share on other sites

Does anyone know if there's enough 800mhz spectrum in bta 52 for a 5×5mhz of lte to be deployed there I've looked at the spectrum maps but I am kind of confused.

I think there is, though I'm not 100% sure. As long as it isn't in SouthernLinc territory I think you're fine.

Link to comment
Share on other sites

I think there is, though I'm not 100% sure. As long as it isn't in SouthernLinc territory I think you're fine.

 

Robert posted a good 800 spectrum map in the premier section.  Looks like the actual amount varies a lot, with the worst areas being SouthernLinc and IBEZ of course.

Link to comment
Share on other sites

Robert posted a good 800 spectrum map in the premier section. Looks like the actual amount varies a lot, with the worst areas being SouthernLinc and IBEZ of course.

Remember IBEZ is not a spectrum constraint rather a usage issue until it is resolved. For example, the western us once resolved will be a 5x5.

Link to comment
Share on other sites

Remember IBEZ is not a spectrum constraint rather a usage issue until it is resolved. For example, the western us once resolved will be a 5x5.

 

I'm well aware of what IBEZ is, just recanting what we already know about 800mhz availability from Robert's spectrum map. 

Link to comment
Share on other sites

From what I seen on the spectrum map that Robert showed there was the same amount across the US. Southernlinc is near the bta I'm in but it still showed sprint as having the same amount as other areas that didn't have southernlinc around. If anyone that knows like aj or Robert would prolly know if there is enough and could give me a definite answer would be nice. I have looked and looked and still have come up confused.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • large.unreadcontent.png.6ef00db54e758d06

  • gallery_1_23_9202.png

  • Similar Content

  • Posts

    • Since this is kind of the general chat thread, I have to share this humorous story (at least it is to me): Since around February/March of this year, my S22U has been an absolute pain to charge. USB-C cables would immediately fall out and it progressively got worse and worse until it often took me a number of minutes to get the angle of the cable juuuussst right to get charging to occur at all (not exaggerating). The connection was so weak that even walking heavily could cause the cable to disconnect. I tried cleaning out the port with a stable, a paperclip, etc. Some dust/lint/dirt came out but the connection didn't improve one bit. Needless to say, this was a MONSTER headache and had me hating this phone. I just didn't have the finances right now for a replacement.  Which brings us to the night before last. I am angry as hell because I had spent five minutes trying to get this phone to charge and failed. I am looking in the port and I notice it doesn't look right. The walls look rough and, using a staple, the back and walls feel REALLY rough and very hard. I get some lint/dust out with the staple and it improves charging in the sense I can get it to charge but it doesn't remove any of the hard stuff. It's late and it's charging, so that's enough for now. I decide it's time to see if that hard stuff is part of the connector or not. More aggressive methods are needed! I work in a biochem lab and we have a lot of different sizes of disposable needles available. So, yesterday morning, while in the lab I grab a few different sizes of needles between 26AWG and 31 AWG. When I got home, I got to work and start probing the connector with the 26 AWG and 31 AWG needle. The stuff feels extremely hard, almost like it was part of the connector, but a bit does break off. Under examination of the bit, it's almost sandy with dust/lint embedded in it. It's not part of the connector but instead some sort of rock-hard crap! That's when I remember that I had done some rock hounding at the end of last year and in January. This involved lots of digging in very sandy/dusty soils; soils which bare more than a passing resemblance to the crap in the connector. We have our answer, this debris is basically compacted/cemented rock dust. Over time, moisture in the area combined with the compression from inserting the USB-C connector had turned it into cement. I start going nuts chiseling away at it with the 26 AWG needle. After about 5-10 minutes of constant chiseling and scraping with the 26AWG and 31AWG needles, I see the first signs of metal at the back of the connector. So it is metal around the outsides! Another 5 minutes of work and I have scraped away pretty much all of the crap in the connector. A few finishing passes with the 31AWG needle, a blast of compressed air, and it is time to see if this helped any. I plug my regular USB-C cable and holy crap it clicks into place; it hasn't done that since February! I pick up the phone and the cable has actually latched! The connector works pretty much like it did over a year ago, it's almost like having a brand new phone!
    • That's odd, they are usually almost lock step with TMO. I forgot to mention this also includes the September Security Update.
    • 417.55 MB September security update just downloaded here for S24+ unlocked   Edit:  after Sept security update install, checked and found a 13MB GP System update as well.  Still showing August 1st there however. 
    • T-Mobile is selling the rest of the 3.45GHz spectrum to Columbia Capital.  
    • Still nothing for my AT&T and Visible phones.
  • Recently Browsing

    • No registered users viewing this page.
×
×
  • Create New...