Jump to content

Google Nexus 5 by LG Users Thread!


nexgencpu

Recommended Posts

Actually, Samsung is the worst in this scenario. Other than PR/VI, all Samsung markets have a different legacy vendor. Therefore, every Samsung LTE site accepted without 3G complete is going to be a problem. Fortunately, Samsung is now flying on 3G acceptances. And has since summer. I would guess they have known since summer, and that's why Samsung has been flying on NV equipment installs for the past 3-4 months.

 

Also, Ericsson has really been pushing on 3G acceptances too the past few months. And at least a lot of Ericsson NV markets have Ericsson (Nortel) legacy equipment.

 

Alcatel Lucent comes off very well in this problem. Since most of their markets heavily focused on 3G deployments up front. And to think the S4GRU members in ALU markets have been so upset and vocal about 3G going in first!

 

The only ALU markets that are a problem are the ones where Motorola is the legacy, but 3G hasn't been upgraded yet. Like the North Carolina markets.

 

Robert via Samsung Note 8.0 using Tapatalk Pro

Actually, I'm in Harrisburg PA served by Shentel which I believe is an "Alcatel Lucent" system. I can't connect to 4G LTE at all with the LG G2.

Link to comment
Share on other sites

Actually, I'm in Harrisburg PA served by Shentel which I believe is an "Alcatel Lucent" system. I can't connect to 4G LTE at all with the LG G2.

The Shentel market is one that totally surprises me.  They are probably the leader in getting their upgrades done.  They are probably well over 90% competed with the upgrading of sites.  Almost all markers on the map are GREEN indicating 3G, 4G, & 800 is complete.

They have a few tough sites yet, like ones on top of high voltage transmission line towers.  So, if they are almost 100% complete, why do I see reports that the N5 is not working.

Is this a simple software update that they need to install in the core switch??  It is totally surprising to me that they are so far advanced in all areas except maybe this issue.

Link to comment
Share on other sites

Actually, I'm in Harrisburg PA served by Shentel which I believe is an "Alcatel Lucent" system. I can't connect to 4G LTE at all with the LG G2.

 

This makes me believe the sites need to advertise eCSFB capability somehow which the new tri band phones are looking for.  Hopefully It's not long before Shentel pushes out an update to 'turn it on'... 

Link to comment
Share on other sites

If eCSFB wasn't part of the original Network Vision 1.0 plan then there might need to be a software update pushed to existing NV1.0 equipment to play nice. The leaked document says "All markets need to be upgraded with eCSFB capability" Perhaps this is why some users have seen their LTE all a sudden start working. Sprint may be in a mad dash to push out software updates for the new eCSFB phones....

Excellent observation. I'm guessing this could be the issue in the ALU NV 3G markets that are not currently working. If this is the case, hopefully Shentel can be brought online quickly for Triband devices.

 

Robert via Samsung Note 8.0 using Tapatalk Pro

Link to comment
Share on other sites

Do you have an educated guess on a time line for this work? Has the upgrades been done but it just hasn't been accepted and turned on, or are they going to have to go through to all the towers to complete more work?

 

Sent from my Nexus 5

It will require a revisit to fire up 3G on these already LTE only enabled sites. Because they will have to fire up equipment and do 911/drive testing. But the good news is all the equipment should already be installed. It's hard to put a time line, because I don't know what kind of resources can be mustered. But I think if made a priority, existing LTE only sites could be NV 3G online nationwide in 60 days.

 

And also from here on out, they can just make sure any new LTE sites also have 3G upgrades installed and accepted with LTE. It would just likely slow down LTE acceptances as 3G acceptances require more testing/integration.

 

Robert via Samsung Note 8.0 using Tapatalk Pro

Link to comment
Share on other sites

It will require a revisit to fire up 3G on these already LTE only enabled sites. Because they will have to fire up equipment and do 911/drive testing. But the good news is all the equipment should already be installed. It's hard to put a time line, because I don't know what kind of resources can be mustered. But I think if made a priority, existing LTE only sites could be NV 3G online nationwide in 60 days.

 

And also from here on out, they can just make sure any new LTE sites also have 3G upgrades installed and accepted with LTE. It would just likely slow down LTE acceptances as 3G acceptances require more testing/integration.

 

Robert via Samsung Note 8.0 using Tapatalk Pro

What about in incumbent markets where it appears that yellow sites are the ones causing issues with connecting?

 

Sent from my Nexus 5 using Tapatalk

 

 

  • Like 1
Link to comment
Share on other sites

What about in incumbent markets where it appears that yellow sites are the ones causing issues with connecting?

 

Sent from my Nexus 5 using Tapatalk

I'm having issues in Lower Westchester county NY, borders the bronx an Alcatel area mostly all yellow.

 

Sent from my Nexus 5 using Tapatalk

 

 

Link to comment
Share on other sites

I don't know how many of you caught the article in CNET from the other day, but T-Mobile confirmed that their full retail price on the Nexus 5 16GB model was $450. They are not receiving them from LG at the price Google is selling them from the Play Store.

Even more evidence that Google is subsidizing these Nexus devices. So please stop posting that Sprint is ripping people off for selling them for $450. It's not Sprint. It's just that buying them from Google is a better deal for consumers. And if that's important to you, buy yours from Google. I did.

http://www.cnet.com/8301-1035_3-57611582-94/heres-why-t-mobiles-nexus-5-is-$100-more-than-at-google-play/

Robert via Samsung Note 8.0 using Tapatalk Pro

  • Like 6
Link to comment
Share on other sites

What about in incumbent markets where it appears that yellow sites are the ones causing issues with connecting?

 

Sent from my Nexus 5 using Tapatalk

We don't have a grasp of every scenario, yet. It is possible that your device has a problem. Will it work in LTE only mode? If so, you probably are suffering from the eCSFB/CSFB problem. If not, then you may have a device problem. And are you certain your site has the same legacy/NV equipment?

 

Robert via Samsung Note 8.0 using Tapatalk Pro

Link to comment
Share on other sites

People with Triband devices are also reporting issues when near the Motherhead site in Cottlevile (near St Louis) which is a yellow pin. They exit the area to where the rest are just 4G and LTE works fine.

Link to comment
Share on other sites

I was so frustrated yesterday with this new Tri Band phone not working in a new equipment area that I took it into a Shentel store.  They checked the device and agreed that:  "Yes, it will not receivr 4G LTE".  But..., they had no information as to when the system would be compatible in my area. 

 

Now, I'm stuck.  I have a Verizon phone number that I wanted to port over to Sprint, but not until I had a working Sprint phone.  Do I wait for them to get this rectified and pay two phone bills in the meantime?

 

I wish there would have been some kind of disclosure on this Spark deployment, as to which markets it was going to be usable in.  I would have waited to avoid all this hassle. 

Link to comment
Share on other sites

We don't have a grasp of every scenario, yet. It is possible that your device has a problem. Will it work in LTE only mode? If so, you probably are suffering from the eCSFB/CSFB problem. If not, then you may have a device problem. And are you certain your site has the same legacy/NV equipment?

 

Robert via Samsung Note 8.0 using Tapatalk Pro

Sites in the 73034 area code are listed as yellow. Forcing LTE does work on these sites. A purple site near my home connects without forcing after toggling airplane mode or making a call.

 

Sent from my Nexus 5 using Tapatalk

 

  • Like 1
Link to comment
Share on other sites

No eFCFB/CSFB problems with the 3G/4G accepted sites on Maryland's Eastern Shore. It is still weird to not see a 1x signal on Signal Check Pro though in 4G areas. I was able to place a call (and watch the 1x signal appear on Signal Check Pro) and then pick up the LTE signal after I hung up.

 

I definitely saw better RF performance on this phone. I was able to hold an LTE signal in an area the One wouldn't. Even in an area that would guarantee losing 3G and often would force roaming on 1x, the Nexus performed better. It never lost the 1x signal and only lost the 3G signal for a short moment.  

  • Like 1
Link to comment
Share on other sites

You will notice in signal check pro when you initiate a call the LTE radio goes idle and CDMA wakes up. Its seamless, and as soon as you hang up it will quickly switch back to LTE. I almost always pick up 1x800 here in my home.

  • Like 4
Link to comment
Share on other sites

You will notice in signal check pro when you initiate a call the LTE radio goes idle and CDMA wakes up. Its seamless, and as soon as you hang up it will quickly switch back to LTE. I almost always pick up 1x800 here in my home.

 

It was seemless, just strange watching it.

Link to comment
Share on other sites

I have a question not related to lte. What is everyone using for voicemail?

 

Sent from my HTCONE using Tapatalk

I can't use Google Voice so voicemail is almost absent as I have no clue if I have voicemail or not. Annoying really, specially because users in the US don't have that problem by using Google Voice.

 

Sent from my Nexus 5 using Tapatalk

 

 

Link to comment
Share on other sites

I can't use Google Voice so voicemail is almost absent as I have no clue if I have voicemail or not. Annoying really, specially because users in the US don't have that problem by using Google Voice.

 

Sent from my Nexus 5 using Tapatalk

 

You have Sprint Voicemail, long press 1 in the dialer and it will call your voicemail. Googlevoice just provides Visual Voicemail.

Link to comment
Share on other sites

You have Sprint Voicemail, long press 1 in the dialer and it will call your voicemail. Googlevoice just provides Visual Voicemail.

It works like that. The thing is I could have any number of voicemail and not be aware of it. That's the problem. No notification.

 

Sent from my Nexus 5 using Tapatalk

 

 

Link to comment
Share on other sites

It works like that. The thing is I could have any number of voicemail and not be aware of it. That's the problem. No notification.

 

Sent from my Nexus 5 using Tapatalk

 

You could try something like this app, which should be compatible with Sprint.

  • Like 1
Link to comment
Share on other sites

It works like that. The thing is I could have any number of voicemail and not be aware of it. That's the problem. No notification.

 

Sent from my Nexus 5 using Tapatalk

You do get missed call notifications, right? I'd base calling voicemail just in case I missed anyone's call.

 

 

Sent from Josh's iPhone 5 using Tapatalk 2

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • large.unreadcontent.png.6ef00db54e758d06

  • gallery_1_23_9202.png

  • Similar Content

  • Posts

    • Since this is kind of the general chat thread, I have to share this humorous story (at least it is to me): Since around February/March of this year, my S22U has been an absolute pain to charge. USB-C cables would immediately fall out and it progressively got worse and worse until it often took me a number of minutes to get the angle of the cable juuuussst right to get charging to occur at all (not exaggerating). The connection was so weak that even walking heavily could cause the cable to disconnect. I tried cleaning out the port with a stable, a paperclip, etc. Some dust/lint/dirt came out but the connection didn't improve one bit. Needless to say, this was a MONSTER headache and had me hating this phone. I just didn't have the finances right now for a replacement.  Which brings us to the night before last. I am angry as hell because I had spent five minutes trying to get this phone to charge and failed. I am looking in the port and I notice it doesn't look right. The walls look rough and, using a staple, the back and walls feel REALLY rough and very hard. I get some lint/dust out with the staple and it improves charging in the sense I can get it to charge but it doesn't remove any of the hard stuff. It's late and it's charging, so that's enough for now. I decide it's time to see if that hard stuff is part of the connector or not. More aggressive methods are needed! I work in a biochem lab and we have a lot of different sizes of disposable needles available. So, yesterday morning, while in the lab I grab a few different sizes of needles between 26AWG and 31 AWG. When I got home, I got to work and start probing the connector with the 26 AWG and 31 AWG needle. The stuff feels extremely hard, almost like it was part of the connector, but a bit does break off. Under examination of the bit, it's almost sandy with dust/lint embedded in it. It's not part of the connector but instead some sort of rock-hard crap! That's when I remember that I had done some rock hounding at the end of last year and in January. This involved lots of digging in very sandy/dusty soils; soils which bare more than a passing resemblance to the crap in the connector. We have our answer, this debris is basically compacted/cemented rock dust. Over time, moisture in the area combined with the compression from inserting the USB-C connector had turned it into cement. I start going nuts chiseling away at it with the 26 AWG needle. After about 5-10 minutes of constant chiseling and scraping with the 26AWG and 31AWG needles, I see the first signs of metal at the back of the connector. So it is metal around the outsides! Another 5 minutes of work and I have scraped away pretty much all of the crap in the connector. A few finishing passes with the 31AWG needle, a blast of compressed air, and it is time to see if this helped any. I plug my regular USB-C cable and holy crap it clicks into place; it hasn't done that since February! I pick up the phone and the cable has actually latched! The connector works pretty much like it did over a year ago, it's almost like having a brand new phone!
    • That's odd, they are usually almost lock step with TMO. I forgot to mention this also includes the September Security Update.
    • 417.55 MB September security update just downloaded here for S24+ unlocked   Edit:  after Sept security update install, checked and found a 13MB GP System update as well.  Still showing August 1st there however. 
    • T-Mobile is selling the rest of the 3.45GHz spectrum to Columbia Capital.  
    • Still nothing for my AT&T and Visible phones.
  • Recently Browsing

    • No registered users viewing this page.
×
×
  • Create New...