Jump to content

LG G2 Users Thread!


koiulpoi

Recommended Posts

Doesn't matter if its a G2 to G2 call.  There are other factors that need to be in place before HD voice will be launched.  Also we don't know the effects of how handing off from a HD voice capable site (NV upgraded) to a non-HD voice capable site (non-NV upgraded) will occur.  Perhaps Sprint might be waiting until NV 1.0 is complete before deploying HD voice.

 

 

I dont know it sounded very different when normally it sounds subpar

 

 

I read somewhere that its the 800 voice that makes the HD part...so if both phones were on 800, then in theory it should be HD

Link to comment
Share on other sites

If thats the case then it couldnt be hd voice. Ericsson is taking a nap when it comes to 800 in the southeast.

I read somewhere that its the 800 voice that makes the HD part...so if both phones were on 800, then in theory it should be HD

  • Like 1
Link to comment
Share on other sites

Nope, beleive it or not I'm not on Spark not even in an area of Spark. The icon has always been on since the update and Sprint is updating WiMax areas first to Spark then the rest and I wasn't in a WiMax area.

 

I'm looking forward to Spark when it does land in my location. :D

Link to comment
Share on other sites

Judging from that speed, you are probably on band 26 or slow band 41 (I say slow 41 because it will go as high as 50+ in band 41). On your phone dialer do ##DEBUG# and look in the LTE Engineering screen for band number when you are connected in that location again.

 

Sent from my LG-LS980 using Tapatalk

 

 

I see 25-34 mbps quite often here on band 25. Especially in the mornings up until noon. It usually see around 15-18 mbps during the day and speeds up to 20-25 in the evening.

 

 

oh and as i understand it....youa re on spark....see that nifty icon on the top...

  

 

The only thing that icon means is that you are on LTE. I wish the Spark icon only showed up for band 41 and the regular LTE icon for band 25/26. I think that would make a lot more sense and help people know when they are in fact on Spark. A blogger who likes to bash Sprint would easily see a Spark icon, get a low speed test on a loaded band 25 connection and simply declare Spark to be a fizzle and further proof of Sprint "lying".

 

i was going to say, that icon is just an icon, doesnt mean band 26 or band 41, just connected to LTE. Ive seen band 25 connections of 35-37mbps before. (albeit on an unloaded site)

Exactly.

Link to comment
Share on other sites

I am just getting LTE band 25 in my area which never was a wimax area but LTE has been here for almost a year. My wife's galaxy s3 gets LTE and I haven't. My speeds on band 25 are about 3Mb up and around 4Mb down.

 

Sent from my LG-LS980 using Tapatalk

 

Edited by SteveO_148
Link to comment
Share on other sites

How can you tell if your phone is in a HD voice call in settings?

While in a call, do a three way call to ##debug# and you will see a screen like this:

Posted Image

 

My wife and I had an HD call today. She was on the G2 and I was using the Flex. Where you see the SO designation you can see it says EVRC_NW. That is HD voice. It was so clear and she was on speaker phone in the bathroom doing her hair. There was no echo and it was perfect!

 

Then she moved to her car and used the car Bluetooth and it went to hell! Probably because the car circuitry is always expecting just 5-8 KHz bandwidth, not the 16 KHz that HD voice uses.

 

Sent from my LG-LS995 using Tapatalk

 

 

  • Like 3
Link to comment
Share on other sites

 

 

I see 25-34 mbps quite often here on band 25. Especially in the mornings up until noon. It usually see around 15-18 mbps during the day and speeds up to 20-25 in the evening.

 

   

 

The only thing that icon means is that you are on LTE. I wish the Spark icon only showed up for band 41 and the regular LTE icon for band 25/26. I think that would make a lot more sense and help people know when they are in fact on Spark. A blogger who likes to bash Sprint would easily see a Spark icon, get a low speed test on a loaded band 25 connection and simply declare Spark to be a fizzle and further proof of Sprint "lying".

 

 

Exactly.

 

I'm not sure if Android natively supports differentiating bands of the same connection type like that with a different icon. I'd rather they use native Android implementations than have to code in proprietary connection icons and such for every phone as they did with CDMA and WiMax originally before native support was available.

  • Like 1
Link to comment
Share on other sites

I'm not sure if Android natively supports differentiating bands of the same connection type like that with a different icon. I'd rather they use native Android implementations than have to code in proprietary connection icons and such for every phone as they did with CDMA and WiMax originally before native support was available.

 

I had my first HD voice call yesterday too here in Ohio. Wonder if they "flipped a switch"?

Link to comment
Share on other sites

I had my first HD voice call yesterday too here in Ohio. Wonder if they "flipped a switch"?

It seems like they did! They can flip a few more switches, and I wouldn't mind as long as they flip the switch to on!

Link to comment
Share on other sites

While in a call, do a three way call to ##debug# and you will see a screen like this:

 

[image removed]

 

My wife and I had an HD call today. She was on the G2 and I was using the Flex. Where you see the SO designation you can see it says EVRC_NW. That is HD voice. It was so clear and she was on speaker phone in the bathroom doing her hair. There was no echo and it was perfect!

 

Then she moved to her car and used the car Bluetooth and it went to hell! Probably because the car circuitry is always expecting just 5-8 KHz bandwidth, not the 16 KHz that HD voice uses.

 

Sent from my LG-LS995 using Tapatalk

 

I believe both devices will need to have that EVRC_NW being reported for it to be a true HD call but I'm thinking that it is a good check from "your" device to see if the base station you are calling though is setup for it.  

Link to comment
Share on other sites

I believe both devices will need to have that EVRC_NW being reported for it to be a true HD call but I'm thinking that it is a good check from "your" device to see if the base station you are calling though is setup for it.

Yeah, they both need the capability, but that codec won't be used if the base stations and other handset don't have HD capability too.

 

Here is a screen grab of my debug screen with me calling a landline:

Posted Image

 

Note it says EVRC instead of EVRC _NW.

 

Sent from my LG-LS995 using Tapatalk

 

 

Link to comment
Share on other sites

While in a call, do a three way call to ##debug# and you will see a screen like this:

tajeby2y.jpg

 

My wife and I had an HD call today. She was on the G2 and I was using the Flex. Where you see the SO designation you can see it says EVRC_NW. That is HD voice. It was so clear and she was on speaker phone in the bathroom doing her hair. There was no echo and it was perfect!

 

Then she moved to her car and used the car Bluetooth and it went to hell! Probably because the car circuitry is always expecting just 5-8 KHz bandwidth, not the 16 KHz that HD voice uses.

 

Sent from my LG-LS995 using Tapatalk

I've seen that before but I've also gotten this

https://www.dropbox.com/s/ht7qfnxf8w2n2dx/Screenshot_2014-01-26-14-48-13.png

 

Idk what it is though

Link to comment
Share on other sites

can somebody summon aj to explain lol

That should be EVRC-B.

 

AJ

  • Like 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • large.unreadcontent.png.6ef00db54e758d06

  • gallery_1_23_9202.png

  • Posts

    • Since this is kind of the general chat thread, I have to share this humorous story (at least it is to me): Since around February/March of this year, my S22U has been an absolute pain to charge. USB-C cables would immediately fall out and it progressively got worse and worse until it often took me a number of minutes to get the angle of the cable juuuussst right to get charging to occur at all (not exaggerating). The connection was so weak that even walking heavily could cause the cable to disconnect. I tried cleaning out the port with a stable, a paperclip, etc. Some dust/lint/dirt came out but the connection didn't improve one bit. Needless to say, this was a MONSTER headache and had me hating this phone. I just didn't have the finances right now for a replacement.  Which brings us to the night before last. I am angry as hell because I had spent five minutes trying to get this phone to charge and failed. I am looking in the port and I notice it doesn't look right. The walls look rough and, using a staple, the back and walls feel REALLY rough and very hard. I get some lint/dust out with the staple and it improves charging in the sense I can get it to charge but it doesn't remove any of the hard stuff. It's late and it's charging, so that's enough for now. I decide it's time to see if that hard stuff is part of the connector or not. More aggressive methods are needed! I work in a biochem lab and we have a lot of different sizes of disposable needles available. So, yesterday morning, while in the lab I grab a few different sizes of needles between 26AWG and 31 AWG. When I got home, I got to work and start probing the connector with the 26 AWG and 31 AWG needle. The stuff feels extremely hard, almost like it was part of the connector, but a bit does break off. Under examination of the bit, it's almost sandy with dust/lint embedded in it. It's not part of the connector but instead some sort of rock-hard crap! That's when I remember that I had done some rock hounding at the end of last year and in January. This involved lots of digging in very sandy/dusty soils; soils which bare more than a passing resemblance to the crap in the connector. We have our answer, this debris is basically compacted/cemented rock dust. Over time, moisture in the area combined with the compression from inserting the USB-C connector had turned it into cement. I start going nuts chiseling away at it with the 26 AWG needle. After about 5-10 minutes of constant chiseling and scraping with the 26AWG and 31AWG needles, I see the first signs of metal at the back of the connector. So it is metal around the outsides! Another 5 minutes of work and I have scraped away pretty much all of the crap in the connector. A few finishing passes with the 31AWG needle, a blast of compressed air, and it is time to see if this helped any. I plug my regular USB-C cable and holy crap it clicks into place; it hasn't done that since February! I pick up the phone and the cable has actually latched! The connector works pretty much like it did over a year ago, it's almost like having a brand new phone!
    • That's odd, they are usually almost lock step with TMO. I forgot to mention this also includes the September Security Update.
    • 417.55 MB September security update just downloaded here for S24+ unlocked   Edit:  after Sept security update install, checked and found a 13MB GP System update as well.  Still showing August 1st there however. 
    • T-Mobile is selling the rest of the 3.45GHz spectrum to Columbia Capital.  
    • Still nothing for my AT&T and Visible phones.
  • Recently Browsing

    • No registered users viewing this page.
×
×
  • Create New...