Jump to content

Everything 800mhz (1xA, LTE, coverage, timeline, etc)


Recommended Posts

My guess is that you can only do two things on one antenna like 1x/lte or 1x/evdo not all three that's just a guess

 

Then why can't they do cdma/lte on one antenna?... Guess just no need for it really...

 

Why I asked to begin with as you have 3 antennas per sector/panel. One does 1900 LTE, one 1900 CDMA/EVDO, and one does 800mhz 1x advance/LTE...

 

Actually if it is right that you can't do more then 2 per antenna that kinda makes some sense if it is laid out how I mention above..... Since they are not doing evdo data on 800 there is no 1x/evdo just 1x/lte...

 

Now the question, I assume it requires 2 carrier cards installed, one for 800 1x advance and one for 800LTE....

 

Sent from my EVO using Tapatalk 2

 

 

Link to comment
Share on other sites

Why did nextel incoming calls or direct connect calls make a clicking sound in car speakers a few seconds before you got the call or 2 way? I'm guessing this was not due to nextel being 800mhz? If not could someone enlighten me.

 

That is a TDMA airlink burst phenomenon. It affects GSM, too.

 

AJ

Link to comment
Share on other sites

That is a TDMA airlink burst phenomenon. It affects GSM, too.

 

AJ

So just Iden and GSM? Never noticed it on a ATT device. It seemed to not happen as much or at all the last few years to some friends that still had IDEN, I had Nextel 13 or 14 years ago even before they provided network time and date and could have my device ready to anwser before it beeped.

Link to comment
Share on other sites

Never noticed it on a ATT device.

 

When have you used an AT&T device? If only in the past few years, then you were likely on W-CDMA (not GSM) 95 percent of the time.

 

AJ

Link to comment
Share on other sites

NV panels do not have three antennas, they have six. Two 800 antennas in the middle and two 1900 on each side. Each antenna can support several carriers. There may be some variability between OEM's. But that's generally the case.

 

Robert via Samsung Note II via Tapatalk

 

 

  • Like 1
Link to comment
Share on other sites

Anyone, trying not to burden Robert when he is so busy, know why a panel has 6 antennas if each antenna can support several carriers?It sounds like you can mix and match CDMA and LTE on one antenna.

Link to comment
Share on other sites

Anyone, trying not to burden Robert when he is so busy, know why a panel has 6 antennas if each antenna can support several carriers?It sounds like you can mix and match CDMA and LTE on one antenna.

 

That would be my argument, too. However, Sprint may wish to use different downtilt settings for different airlinks in the same band, and that requires separate antennas. Not to mention, LTE requires a MIMO configuration, while CDMA2000 does not.

 

AJ

Link to comment
Share on other sites

NV panels do not have three antennas, they have six. Two 800 antennas in the middle and two 1900 on each side. Each antenna can support several carriers. There may be some variability between OEM's. But that's generally the case.

 

Robert via Samsung Note II via Tapatalk

 

Ahhh ok perfect sense there. I just assumed that sense there were 3 actuators on the bottom to adjust tilt that it was only 3 antennas.

 

Sent from my EVO using Tapatalk 2

 

 

Link to comment
Share on other sites

That is a TDMA airlink burst phenomenon. It affects GSM, too.

 

AJ

By the way, googling "TDMA airlink burst phenomenon" without quotes brings up this thread as the first result :P
  • Like 2
Link to comment
Share on other sites

By the way, googling "TDMA airlink burst phenomenon" without quotes brings up this thread as the first result :P

 

I take it then that I have a distinctive voice.

 

;)

 

AJ

  • Like 3
Link to comment
Share on other sites

How can you tell if you're on SMR on the iPhone 5? What do I need to look for in the field test app?

 

Two things: band class 10, carrier channel 476 or 526.

 

That said, if I recall correctly, our resident PRL expert, digiblur, has stated that iPhones have not received an SMR enabled PRL yet. So, SMR acquisition on an iPhone 5 is highly unlikely.

 

AJ

Link to comment
Share on other sites

 

 

Two things: band class 10, carrier channel 476 or 526.

 

That said, if I recall correctly, our resident PRL expert, digiblur, has stated that iPhones have not received an SMR enabled PRL yet. So, SMR acquisition on an iPhone 5 is highly unlikely.

 

AJ

 

Hm... I could have sworn that the new prl, 55012 added SMR for the north bay (San Francisco, Vallejo, etc)

Link to comment
Share on other sites

55012 on my i5 here in Austin too, but a couple weeks ago it was 3xxxx (I forgot exactly which)

 

 

Hm... I could have sworn that the new prl, 55012 added SMR for the north bay (San Francisco, Vallejo, etc)

 

 

pretty sure it was prl 25012 is what added the smr, not 55012

  • Like 1
Link to comment
Share on other sites

800 mhz is back up here after not seeing it for a couple weeks. Went over to a relatives house this evening where I usually roam on Verizon on 1900, but had a nice -98ish dbm signal on 800. This would be an 8.34 mile link according to Google Earth. Before, I could sometimes coax a 1900 signal from that same tower (only tower in range), but it'd be too weak to hold for more than a minute or so.

  • Like 3
Link to comment
Share on other sites

Does sprint's 800MHz SMR support CDMA/1xA Data or is it just voice only?

 

It supports 1x data also.

 

Robert via Nexus 7 with Tapatalk HD

  • Like 2
Link to comment
Share on other sites

Considering that there will be one 1x carrier and that's it, is it possible that it could be strained by data use? There will certainly be times when people have 1x 800 but can't connect to 1900 PCS. What is the fully loaded data capacity of 1x? I know it's 144 kbps or so per mobile, but what about in the aggregate?

Link to comment
Share on other sites

Considering that there will be one 1x carrier and that's it, is it possible that it could be strained by data use? There will certainly be times when people have 1x 800 but can't connect to 1900 PCS. What is the fully loaded data capacity of 1x? I know it's 144 kbps or so per mobile, but what about in the aggregate?

 

That is not a simple question to answer. For CDMA1X data, the most common (or, seemingly, the only permitted) radio configuration is RC3, which permits a max transfer rate of 153.6 kbps (oft quoted as 144 kbps). At the max rate, RC3 precludes use of one quarter of all codes in the Walsh tree. In plain English, it takes up one quarter of the capacity of the CDMA1X carrier. But RC3 does not operate at max rate unless capacity is available.

 

That is the nutshell answer. Feel free to ask follow up questions.

 

AJ

  • Like 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • large.unreadcontent.png.6ef00db54e758d06

  • gallery_1_23_9202.png

  • Similar Content

  • Posts

    • Since this is kind of the general chat thread, I have to share this humorous story (at least it is to me): Since around February/March of this year, my S22U has been an absolute pain to charge. USB-C cables would immediately fall out and it progressively got worse and worse until it often took me a number of minutes to get the angle of the cable juuuussst right to get charging to occur at all (not exaggerating). The connection was so weak that even walking heavily could cause the cable to disconnect. I tried cleaning out the port with a stable, a paperclip, etc. Some dust/lint/dirt came out but the connection didn't improve one bit. Needless to say, this was a MONSTER headache and had me hating this phone. I just didn't have the finances right now for a replacement.  Which brings us to the night before last. I am angry as hell because I had spent five minutes trying to get this phone to charge and failed. I am looking in the port and I notice it doesn't look right. The walls look rough and, using a staple, the back and walls feel REALLY rough and very hard. I get some lint/dust out with the staple and it improves charging in the sense I can get it to charge but it doesn't remove any of the hard stuff. It's late and it's charging, so that's enough for now. I decide it's time to see if that hard stuff is part of the connector or not. More aggressive methods are needed! I work in a biochem lab and we have a lot of different sizes of disposable needles available. So, yesterday morning, while in the lab I grab a few different sizes of needles between 26AWG and 31 AWG. When I got home, I got to work and start probing the connector with the 26 AWG and 31 AWG needle. The stuff feels extremely hard, almost like it was part of the connector, but a bit does break off. Under examination of the bit, it's almost sandy with dust/lint embedded in it. It's not part of the connector but instead some sort of rock-hard crap! That's when I remember that I had done some rock hounding at the end of last year and in January. This involved lots of digging in very sandy/dusty soils; soils which bare more than a passing resemblance to the crap in the connector. We have our answer, this debris is basically compacted/cemented rock dust. Over time, moisture in the area combined with the compression from inserting the USB-C connector had turned it into cement. I start going nuts chiseling away at it with the 26 AWG needle. After about 5-10 minutes of constant chiseling and scraping with the 26AWG and 31AWG needles, I see the first signs of metal at the back of the connector. So it is metal around the outsides! Another 5 minutes of work and I have scraped away pretty much all of the crap in the connector. A few finishing passes with the 31AWG needle, a blast of compressed air, and it is time to see if this helped any. I plug my regular USB-C cable and holy crap it clicks into place; it hasn't done that since February! I pick up the phone and the cable has actually latched! The connector works pretty much like it did over a year ago, it's almost like having a brand new phone!
    • That's odd, they are usually almost lock step with TMO. I forgot to mention this also includes the September Security Update.
    • 417.55 MB September security update just downloaded here for S24+ unlocked   Edit:  after Sept security update install, checked and found a 13MB GP System update as well.  Still showing August 1st there however. 
    • T-Mobile is selling the rest of the 3.45GHz spectrum to Columbia Capital.  
    • Still nothing for my AT&T and Visible phones.
  • Recently Browsing

    • No registered users viewing this page.
×
×
  • Create New...