Jump to content

Official Airave 4 LTE / Casa Pebble / Airave 3 LTE / S1000 Thread


SeanK_

Recommended Posts

Try dialing *99 and see if you hear the pre-recorded message ("You are now within Airave Coverage."). 
I have tried that, but it says the feature code is not valid. Attached is a screenshot while on a call. I essentially have zero voice service from the macro network at my house and this is the only way to get any voice service, so it must be going through the Airave. Maybe the 4 doesn't give an audible signal like the older units do? On another note, does anybody know if there 4 will eventually support VoLTE?cb2d1113a393ca149aead1f707b45790.jpg

Sent from my SM-G950U using Tapatalk

Link to comment
Share on other sites

Can you limit which phones (whitelist) use the Airave 4?
I do see the same option to whitelist or blacklist numbers for the 4 under manage my Airave.

Sent from my SM-G950U using Tapatalk

Link to comment
Share on other sites

So it's up and running. Here's a screenshot from signal check pro. It looks like I'm connected to the voice side, but when I place a call I don't hear the 3 beeps.


Thanks for sharing! You don't have a Magic Box nearby, do you? Just want to confirm so I can try to make adjustments to SCP.

-Mike
Link to comment
Share on other sites



Thanks for sharing! You don't have a Magic Box nearby, do you? Just want to confirm so I can try to make adjustments to SCP.

-Mike
No problem! I don't have a magic box, and I don't believe anybody near me has one either, since service is so terrible where I am. Do you want me to send some logs your way?

Sent from my SM-G950U using Tapatalk

  • Like 1
Link to comment
Share on other sites

No problem! I don't have a magic box, and I don't believe anybody near me has one either, since service is so terrible where I am. Do you want me to send some logs your way?


I thought I replied earlier, but I don't see it now.. if you (or anyone else who connects to an Airave 4) could send a diagnostic report through SCP, I would appreciate it! I only need one report per Airave, but the more I get the quicker I can learn how to properly identify it in SCP. Please note on the report that it's an Airave 4 connection so I can keep track. Thanks!

-Mike
  • Like 3
Link to comment
Share on other sites



I thought I replied earlier, but I don't see it now.. if you (or anyone else who connects to an Airave 4) could send a diagnostic report through SCP, I would appreciate it! I only need one report per Airave, but the more I get the quicker I can learn how to properly identify it in SCP. Please note on the report that it's an Airave 4 connection so I can keep track. Thanks!

-Mike
Just sent one your way! If you need anything else, just let me know.

Sent from my SM-G950U using Tapatalk

  • Thanks 1
Link to comment
Share on other sites

My airave 4 is coming today! Those who have it already, is there a decrease in internet speed with other devices on wifi?
I'm not sure what you mean by this. If you are actively using LTE on it, then it will reduce the speed available to other devices. Just like if you were on wifi and using data. For example, if your home internet is 100 Mbps, and you're doing a speed test or something else that is consuming 40 Mbps via the Airave, then there is 60 Mbps left for other devices on wifi. But if there is no active data transfer occurring via the Airave (ie your phone is idle), then it won't be using your internet.

It's basically the same as if your phone was on wifi.


Sent from my Pixel 3 XL using Tapatalk

Link to comment
Share on other sites

On 5/26/2019 at 5:48 PM, mikejeep said:

 


I thought I replied earlier, but I don't see it now.. if you (or anyone else who connects to an Airave 4) could send a diagnostic report through SCP, I would appreciate it! I only need one report per Airave, but the more I get the quicker I can learn how to properly identify it in SCP. Please note on the report that it's an Airave 4 connection so I can keep track. Thanks!

-Mike

 

Just got my replacement and just sent you a log. Do you also want the LTE Engineering or anything too?

Link to comment
Share on other sites

Just got my replacement and just sent you a log. Do you also want the LTE Engineering or anything too?
It hunk he'll take any and everything. Hell load up NSG as well if you have access to that!

Sent from my Pixel 3 using Tapatalk

Link to comment
Share on other sites

Just got my replacement and just sent you a log. Do you also want the LTE Engineering or anything too?


Thanks! I only need that report, but I'm sure the rest of the group would love screenshots here of whatever you have..

-Mike
Link to comment
Share on other sites

Well if anyone interested in the debug screenshots https://imgur.com/a/EdrPKwt
That's connected to the Airave? That looks like a macro earfcn, 41374. The last Airave always used the first carrier earfcn, but it appeared that this one would use the MB earfcn. Now that seems less certain. What are the macro B41 earfcns in your area?

It also looks like the CDMA side supports 1xAdvanced (and presumably HD voice).

Sent from my Pixel 3 XL using Tapatalk

Link to comment
Share on other sites

7 minutes ago, ingenium said:

That's connected to the Airave? That looks like a macro earfcn, 41374. The last Airave always used the first carrier earfcn, but it appeared that this one would use the MB earfcn. Now that seems less certain. What are the macro B41 earfcns in your area?

It also looks like the CDMA side supports 1xAdvanced (and presumably HD voice).

Sent from my Pixel 3 XL using Tapatalk
 

Yup,There is no B41 near me that I can get, so far I'm only able to attach to B25 and B26 (very weak signals). I currently don't have the earfcns off the top of my head. I can grab that when I'm out and about tomorrow.

Link to comment
Share on other sites

My Airave 4 is up and running with CDMA only. LTE is always blinking red. Not sure why. Does it has a separate MAC address for LTE side? My cooperate network requires MAC address whitelisting. I whitelisted the MAC address on the label. The CDMA voice works fine. LTE don't. I don't needed LTE anyway. :) The building has good T-mobile B66.

  • Haha 1
Link to comment
Share on other sites

9 minutes ago, dnwk said:

My Airave 4 is up and running with CDMA only. LTE is always blinking red. Not sure why. Does it has a separate MAC address for LTE side? My cooperate network requires MAC address whitelisting. I whitelisted the MAC address on the label. The CDMA voice works fine. LTE don't. I don't needed LTE anyway. :) The building has good T-mobile B66.

Could be being blocked by your corporate firewall or it's having NAT issues. 

Link to comment
Share on other sites

4 minutes ago, Brad The Beast said:

Could be being blocked by your corporate firewall or it's having NAT issues. 

But CDMA side works fine. And I don't have problem with Airave 3

Link to comment
Share on other sites

My Airave 4 is up and running with CDMA only. LTE is always blinking red. Not sure why. Does it has a separate MAC address for LTE side? My cooperate network requires MAC address whitelisting. I whitelisted the MAC address on the label. The CDMA voice works fine. LTE don't. I don't needed LTE anyway. [emoji4] The building has good T-mobile B66.
Same MAC address, but it uses 2 IPsec tunnels. It's possible that the LTE one is getting blocked. On the 3 it always initiates the CDMA side first, so if your network only allows 1 IPsec connection per device for some reason, it would explain why the CDMA side works.

I'm pretty sure it doesn't need ipsec passthrough help, since it defaults to ipsec over UDP, but I could be mistaken on that.

Sent from my Pixel 3 XL using Tapatalk

Link to comment
Share on other sites

But CDMA side works fine. And I don't have problem with Airave 3
In that case I'm not sure. I won't have mine until the end of the week, so I can't do a packet capture to analyze. I'd say just leave it overnight and see if it's working in the morning.

Sent from my Pixel 3 XL using Tapatalk

Link to comment
Share on other sites

3 minutes ago, ingenium said:

In that case I'm not sure. I won't have mine until the end of the week, so I can't do a packet capture to analyze. I'd say just leave it overnight and see if it's working in the morning.

Sent from my Pixel 3 XL using Tapatalk
 

Thanks. Let me know what you found. I doesn't really need LTE since there is pretty good T-mobile LTE. I just need voice coverage.

Link to comment
Share on other sites

I just got my Airave 4 LTE. It seems like time on my phone is now switched to 1 hour off. I suspect it being the airave causing this problem as my phone is set to automatic time. Any ideas what I need to do?

Link to comment
Share on other sites

1 minute ago, hsiaoandrew said:

I just got my Airave 4 LTE. It seems like time on my phone is now switched to 1 hour off. I suspect it being the airave causing this problem as my phone is set to automatic time. Any ideas what I need to do?

I would recommend you contact support and have them put a ticket in.

  • Like 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • large.unreadcontent.png.6ef00db54e758d06

  • gallery_1_23_9202.png

  • Similar Content

  • Posts

    • A heavy n41 overlay as an acquisition condition would be a win for customers, and eventually a win for T-Mobile as that might be enough to preclude VZW/AT&T adding C-Band for FWA due to spreading the market too thinly (which means T-Mobile would just have local WISPs/wireline ISPs as competition). USCC spacing (which is likely for contiguous 700 MHz LTE coverage in rural areas) isn't going to be enough for contiguous n41 anyway, and I doubt they'll densify enough to get there.
    • Boost Infinite with a rainbow SIM (you can get it SIM-only) is the cheapest way, at $25/mo, to my knowledge; the cheaper Boost Mobile plans don't run on Dish native. Check Phonescoop for n70 support on a given phone; the Moto G 5G from last year may be the cheapest unlocked phone with n70 though data speeds aren't as good as something with an X70 or better modem.
    • Continuing the USCC discussion, if T-Mobile does a full equipment swap at all of USCC's sites, which they probably will for vendor consistency, and if they include 2.5 on all of those sites, which they probably will as they definitely have economies of scale on the base stations, that'll represent a massive capacity increase in those areas over what USCC had, and maybe a coverage increase since n71 will get deployed everywhere and B71 will get deployed any time T-Mobile has at least 25x25, and maybe where they have 20x20. Assuming this deal goes through (I'm betting it does), I figure I'll see contiguous coverage in the area of southern IL where I was attempting to roam on USCC the last time I was there, though it might be late next year before that switchover happens.
    • Forgot to post this, but a few weeks ago I got to visit these small cells myself! They're spread around Grant park and the surrounding areas, but unfortunately none of the mmwave cells made it outside of the parks along the lake into the rest of downtown. I did spot some n41 small cells around downtown, but they seemed to be older deployments limited to 100mhz and performed poorly.    
    • What is the cheapest way to try Dish's wireless network?  Over the past year I've seen them add their equipment to just about every cell site here, I'm assuming just go through Boost's website?  What phones are Dish native?  
  • Recently Browsing

    • No registered users viewing this page.
×
×
  • Create New...