Jump to content

Will my LTE get better?


Recommended Posts

(still new to this stuff go easy on me)

 

I live in an area that has been having NV LTE upgrades since december...Petaluma, CA. Everywhere I go i am connected to cdma 800 sites for voice (i have signalcheck pro) and all of my towers seem to be eHRPD. Sometimes I connect to LTE, sometimes I do not. I have a tower about 1 mile away from my work which is the next town over and can connect frequently but the signal seems poor and drops to 3G when I am past -125dBm. Should my signal strength be so low for the tower only being 1 mile away? I have called sprint and sometimes they tell me that all work has been done for my area other times they say things are still being upgraded and not til the end of the year will I see consistent strength and speeds. I usually see 5-8mbps unless I am really close then it's upper 20's. I am using an HTC ONE by the way and the wife has an iphone 5 which seems to grab the LTE signal way earlier and longer when I am in fringe areas. So is this range normal for LTE towers, seems kind of weak to me, i mean the cdma 800 tower I am connected to is like 10 miles away with a -95dBm and almost full bars. 

Link to comment
Share on other sites

I was sitting about 1/4 mile or less from the Hardeeville, SC cellular site today, and I was getting -65db on 1xRTT... And -95db on LTE.. I lose the LTE signal about two miles from it.. It is not an urban site at all... Same thing with the new Myrtle Beach, SC one...

 

Notice that we both have the EVOLTE... Just sucks on LTE... Hope my Galaxy Note 3 will do better. :)

Link to comment
Share on other sites

I was sitting about 1/4 mile or less from the Hardeeville, SC cellular site today, and I was getting -65db on 1xRTT... And -95db on LTE.. I lose the LTE signal about two miles from it.. It is not an urban site at all... Same thing with the new Myrtle Beach, SC one...

 

Notice that we both have the EVOLTE... Just sucks on LTE... Hope my Galaxy Note 3 will do better. :)

he is using an htc one :D    but signal strength varies greatly from site to site depending on surroundings and downtilt 

  • Like 1
Link to comment
Share on other sites

he is using an htc one :D    but signal strength varies greatly from site to site depending on surroundings and downtilt

 

Oops... I see that now. My bad. Need to watch for the details better, I guess...

 

SO.... How IS the One for LTE? And AM I seeing such lower strength readings when comparing the 1X and LTE because of my EVOLTE or is there a different down tilt on one or the other? (Both sites pretty rural)...

Link to comment
Share on other sites

I have the HTC one. It does not as good as lte as my gnex or LG OG did. Also in my site none of our ones can keep connected to lte in the back of the site where every other phone arrays connected fine.

 

Sent from my HTCONE using Tapatalk 4

 

 

Link to comment
Share on other sites

Down tilt of each antenna can vary (housed inside a panel) at the sprint site,  but the EVO LTE in general blows in terms of lte connectivity. Htc one is a lot better then the EVO LTE in terms of lte connectivity but does still lag behind the S3 and S4 in acquiring the lte signal. LTE signal is fragile and requires a stronger link to work, so your signal will never be as good as your 1x (unless standing or in a car close to the site) 

 

 

edit: my 1234 post :D

Link to comment
Share on other sites

(still new to this stuff go easy on me)

 

I live in an area that has been having NV LTE upgrades since december...Petaluma, CA. Everywhere I go i am connected to cdma 800 sites for voice (i have signalcheck pro) and all of my towers seem to be eHRPD. Sometimes I connect to LTE, sometimes I do not. I have a tower about 1 mile away from my work which is the next town over and can connect frequently but the signal seems poor and drops to 3G when I am past -125dBm. Should my signal strength be so low for the tower only being 1 mile away? I have called sprint and sometimes they tell me that all work has been done for my area other times they say things are still being upgraded and not til the end of the year will I see consistent strength and speeds. I usually see 5-8mbps unless I am really close then it's upper 20's. I am using an HTC ONE by the way and the wife has an iphone 5 which seems to grab the LTE signal way earlier and longer when I am in fringe areas. So is this range normal for LTE towers, seems kind of weak to me, i mean the cdma 800 tower I am connected to is like 10 miles away with a -95dBm and almost full bars. 

 

It's not that the tower is weak, but many sites in urban, even suburban sites are set up to cover only a couple of miles, sometimes even less so that they can pack more sites into the area to increase capacity. 

 

It's also possible that you aren't connecting to the site you think you are. If you can tell us a little more about your location, we can tell you how NV is progressing in that region.

 

 

Oops... I see that now. My bad. Need to watch for the details better, I guess...

 

SO.... How IS the One for LTE? And AM I seeing such lower strength readings when comparing the 1X and LTE because of my EVOLTE or is there a different down tilt on one or the other? (Both sites pretty rural)...

 

What are you using to look at signal strengths? LTE is measured in RSRP whereas 1x and EVDO in RSSI. LTE is inherently "weaker" because you need a stronger signal for it to work that EVDO or 1x needs. The EVO LTE is also notoriously weak for LTE.

 

The ONE is much better than the EVO LTE. I've owned the LTE, GS3, and currently the ONE. From my experience the ONE is nearly on par with the GS3. 

  • Like 1
Link to comment
Share on other sites

I was sitting about 1/4 mile or less from the Hardeeville, SC cellular site today, and I was getting -65db on 1xRTT... And -95db on LTE.. I lose the LTE signal about two miles from it.. It is not an urban site at all... Same thing with the new Myrtle Beach, SC one...

 

Notice that we both have the EVOLTE... Just sucks on LTE... Hope my Galaxy Note 3 will do better. :)

Remember that you can be on 1xrtt on one tower and lte on another.
Link to comment
Share on other sites

Using the Signalcheck pro....

 

It's not that the tower is weak, but many sites in urban, even suburban sites are set up to cover only a couple of miles, sometimes even less so that they can pack more sites into the area to increase capacity. 

 

It's also possible that you aren't connecting to the site you think you are. If you can tell us a little more about your location, we can tell you how NV is progressing in that region.

 

 

 

 

What are you using to look at signal strengths? LTE is measured in RSRP whereas 1x and EVDO in RSSI. LTE is inherently "weaker" because you need a stronger signal for it to work that EVDO or 1x needs. The EVO LTE is also notoriously weak for LTE.

 

The ONE is much better than the EVO LTE. I've owned the LTE, GS3, and currently the ONE. From my experience the ONE is nearly on par with the GS3.

 

Link to comment
Share on other sites

(still new to this stuff go easy on me)

 

I live in an area that has been having NV LTE upgrades since december...Petaluma, CA. Everywhere I go i am connected to cdma 800 sites for voice (i have signalcheck pro) and all of my towers seem to be eHRPD. Sometimes I connect to LTE, sometimes I do not. I have a tower about 1 mile away from my work which is the next town over and can connect frequently but the signal seems poor and drops to 3G when I am past -125dBm. Should my signal strength be so low for the tower only being 1 mile away? I have called sprint and sometimes they tell me that all work has been done for my area other times they say things are still being upgraded and not til the end of the year will I see consistent strength and speeds. I usually see 5-8mbps unless I am really close then it's upper 20's. I am using an HTC ONE by the way and the wife has an iphone 5 which seems to grab the LTE signal way earlier and longer when I am in fringe areas. So is this range normal for LTE towers, seems kind of weak to me, i mean the cdma 800 tower I am connected to is like 10 miles away with a -95dBm and almost full bars. 

 

You'll see a much better experience once the other towers in the cluster are upgraded and broadcasting LTE.

 

In my local town, they upgraded one of the sites a mile away to NV LTE, and adjusted the tilt slightly, so I was getting a faint (-110dB) LTE signal, vs. connected to the legacy 3G site about a block and half away. At home, my phone would bounce between towers. Once they upgraded the site closer to my house to NV LTE, all my issues went away.

  • Like 1
Link to comment
Share on other sites

Oops... I see that now. My bad. Need to watch for the details better, I guess...

 

SO.... How IS the One for LTE? And AM I seeing such lower strength readings when comparing the 1X and LTE because of my EVOLTE or is there a different down tilt on one or the other? (Both sites pretty rural)...

Using the Signalcheck pro....

 

Are you not aware of the differences between CDMA1X RSSI and LTE RSRP?  You cannot simply compare the signal strength numbers directly.

 

AJ

Link to comment
Share on other sites

Are you not aware of the differences between CDMA1X RSSI and LTE RSRP?  You cannot simply compare the signal strength numbers directly.

 

AJ

I guess I am not... So if the Signalcheck Pro app was showing a -95dBm on LTE and -65dBm on 1X very close to the site in Hardeeville... And around 1 mile from the site in Myrtle Beach I was getting -117dBm on LTE right before I lost it and went to ehrpd (and around -96dBm on 1x) ... What numbers are these (rsrp and rssi)? What is the real world meaning of all of this? Bad phone, bad tilts, etc?

Link to comment
Share on other sites

I guess I am not... So if the Signalcheck Pro app was showing a -95dBm on LTE and -65dBm on 1X very close to the site in Hardeeville... And around 1 mile from the site in Myrtle Beach I was getting -117dBm on LTE right before I lost it and went to ehrpd (and around -96dBm on 1x) ... What numbers are these (rsrp and rssi)? What is the real world meaning of all of this? Bad phone, bad tilts, etc?

 

Well, we have written and posted about the differences between RSSI and RSRP a lot.  But if you have not yet come across that info, I suggest that you start with the following article and thread:

 

http://s4gru.com/index.php?/blog/1/entry-308-rssi-vs-rsrp-a-brief-lte-signal-strength-primer/

http://s4gru.com/index.php?/topic/2040-bars-lie-for-lte-signal-strength-how-to-determine-your-actual-lte-signal-strength/

 

AJ

  • Like 3
Link to comment
Share on other sites

Well, we have written and posted about the differences between RSSI and RSRP a lot.  But if you have not yet come across that info, I suggest that you start with the following article and thread:

 

http://s4gru.com/index.php?/blog/1/entry-308-rssi-vs-rsrp-a-brief-lte-signal-strength-primer/

http://s4gru.com/index.php?/topic/2040-bars-lie-for-lte-signal-strength-how-to-determine-your-actual-lte-signal-strength/

 

AJ

Thank you! What I get out of that is the lower number on the LTE is better than a lower 1X number... Very interesting read, thanks for having written it...

Link to comment
Share on other sites

I guess I am not... So if the Signalcheck Pro app was showing a -95dBm on LTE and -65dBm on 1X very close to the site in Hardeeville... And around 1 mile from the site in Myrtle Beach I was getting -117dBm on LTE right before I lost it and went to ehrpd (and around -96dBm on 1x) ... What numbers are these (rsrp and rssi)? What is the real world meaning of all of this? Bad phone, bad tilts, etc?

 

Around -95dBm RSSI on 1x is about the extent of the range of LTE. So that sounds about right. Sounds like you have rather tight site spacing around there if you were only about a mile away. That just means it will take several more site upgrades before LTE covers a wider area since the sites are set up to cover a small area. In rural regions, sites can cover up to 10+ miles, whereas in densely populated areas they can be set up to cover only a couple blocks.

Link to comment
Share on other sites

Around -95dBm RSSI on 1x is about the extent of the range of LTE. So that sounds about right. Sounds like you have rather tight site spacing around there if you were only about a mile away. That just means it will take several more site upgrades before LTE covers a wider area since the sites are set up to cover a small area. In rural regions, sites can cover up to 10+ miles, whereas in densely populated areas they can be set up to cover only a couple blocks..

The site in question upon looking at the maps was around 3 to 5 miles away from the nearby cell sites...  So it still seems like to me there would be large spaces between each site without useable LTE reaching from one to the next... This seems to apply to both of the 4G locations I have been paying much attention to (I am able to play with only the two locations so far in the travels my job takes me in)... not nearly the coverage from the LTE at each one to make it to the next cell site's coverage.  The next thing I will have to do is play with my wife's S4 and see how that does next time the two of us are on the south end of Myrtle Beach...  I am really not to worried, it isn't like this forum is full of people in mature NV markets that are dealing with a bunch of small LTE islands, rather more just interested and curious.

 

BTW, sorry OP for stealing your thread!!

Link to comment
Share on other sites

The site in question upon looking at the maps was around 3 to 5 miles away from the nearby cell sites...  So it still seems like to me there would be large spaces between each site without useable LTE reaching from one to the next... This seems to apply to both of the 4G locations I have been paying much attention to (I am able to play with only the two locations so far in the travels my job takes me in)... not nearly the coverage from the LTE at each one to make it to the next cell site's coverage.  The next thing I will have to do is play with my wife's S4 and see how that does next time the two of us are on the south end of Myrtle Beach...  I am really not to worried, it isn't like this forum is full of people in mature NV markets that are dealing with a bunch of small LTE islands, rather more just interested and curious.

 

BTW, sorry OP for stealing your thread!!

 

I'll take a look at the maps, see what's going on. Can you PM me or post in one of the sponsor threads the specific sites? I'm just curious as to how they're set up.

Link to comment
Share on other sites

 I am really not to worried, it isn't like this forum is full of people in mature NV markets that are dealing with a bunch of small LTE islands, rather more just interested and curious.

 

 

see phoenix lol.. we are dealing with just that... about half of phoenix available sites are nv 3g complete and so far we have two islands of lte... so your problem is our problem lol in fact similar questions have been brought up in our threads. we have people connected to a nearby 1xrtt and trying to figure out if the lte they are connected to several miles away is actually the lte site that we know about, or... another unknown site.. because when that op went to see the site couldn't connect but he did get lte 4 miles away  

 

in that case we were relatively sure that its tower he tried to connect to and not an unknown one, and was just the tilt of the panels...  

Link to comment
Share on other sites

I don't understand why I can connect to my LTE towers on some days and not on others, I just wish sprint would let me know if they are still working on my area. All week i have been connecting to 1x800 and today it was 1xrtt. Same route, same towers everyday. My service is so inconsistant, it's way better than it has been in the past but still can go from 37mbps to .1 within a few blocks.

  • Like 1
Link to comment
Share on other sites

I don't understand why I can connect to my LTE towers on some days and not on others, I just wish sprint would let me know if they are still working on my area. All week i have been connecting to 1x800 and today it was 1xrtt. Same route, same towers everyday. My service is so inconsistant, it's way better than it has been in the past but still can go from 37mbps to .1 within a few blocks.

 

The site in the middle of town at Washington and Telephone has yet to be upgraded to LTE, so that may be part of your issue. 

Link to comment
Share on other sites

the two towers i would connect to the most would be on caufield ln petaluma, and i think the one by my work is near commerce and expressway in rohnert park, ca. the one near my work is only 1 mile away from my work and still LTE drops or is at a teetering -125dBm. 1 mile doesn't seem like asking for much.

Link to comment
Share on other sites

the two towers i would connect to the most would be on caufield ln petaluma, and i think the one by my work is near commerce and expressway in rohnert park, ca. the one near my work is only 1 mile away from my work and still LTE drops or is at a teetering -125dBm. 1 mile doesn't seem like asking for much.

 

If you're a mile away, that means you're already closer to a different site. Sites in pretty populated areas like that are generally configured to cover less than a mile.

Link to comment
Share on other sites

If you're a mile away, that means you're already closer to a different site. Sites in pretty populated areas like that are generally configured to cover less than a mile.

I can agree with this since the tower nearest me, .25-.33 miles is not lit up and the other towers are just over 1.125 miles from work.  i go one block in any direction and i get faint LTE but once i get to the job, it's gone.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • large.unreadcontent.png.6ef00db54e758d06

  • gallery_1_23_9202.png

  • Posts

    • Since this is kind of the general chat thread, I have to share this humorous story (at least it is to me): Since around February/March of this year, my S22U has been an absolute pain to charge. USB-C cables would immediately fall out and it progressively got worse and worse until it often took me a number of minutes to get the angle of the cable juuuussst right to get charging to occur at all (not exaggerating). The connection was so weak that even walking heavily could cause the cable to disconnect. I tried cleaning out the port with a stable, a paperclip, etc. Some dust/lint/dirt came out but the connection didn't improve one bit. Needless to say, this was a MONSTER headache and had me hating this phone. I just didn't have the finances right now for a replacement.  Which brings us to the night before last. I am angry as hell because I had spent five minutes trying to get this phone to charge and failed. I am looking in the port and I notice it doesn't look right. The walls look rough and, using a staple, the back and walls feel REALLY rough and very hard. I get some lint/dust out with the staple and it improves charging in the sense I can get it to charge but it doesn't remove any of the hard stuff. It's late and it's charging, so that's enough for now. I decide it's time to see if that hard stuff is part of the connector or not. More aggressive methods are needed! I work in a biochem lab and we have a lot of different sizes of disposable needles available. So, yesterday morning, while in the lab I grab a few different sizes of needles between 26AWG and 31 AWG. When I got home, I got to work and start probing the connector with the 26 AWG and 31 AWG needle. The stuff feels extremely hard, almost like it was part of the connector, but a bit does break off. Under examination of the bit, it's almost sandy with dust/lint embedded in it. It's not part of the connector but instead some sort of rock-hard crap! That's when I remember that I had done some rock hounding at the end of last year and in January. This involved lots of digging in very sandy/dusty soils; soils which bare more than a passing resemblance to the crap in the connector. We have our answer, this debris is basically compacted/cemented rock dust. Over time, moisture in the area combined with the compression from inserting the USB-C connector had turned it into cement. I start going nuts chiseling away at it with the 26 AWG needle. After about 5-10 minutes of constant chiseling and scraping with the 26AWG and 31AWG needles, I see the first signs of metal at the back of the connector. So it is metal around the outsides! Another 5 minutes of work and I have scraped away pretty much all of the crap in the connector. A few finishing passes with the 31AWG needle, a blast of compressed air, and it is time to see if this helped any. I plug my regular USB-C cable and holy crap it clicks into place; it hasn't done that since February! I pick up the phone and the cable has actually latched! The connector works pretty much like it did over a year ago, it's almost like having a brand new phone!
    • That's odd, they are usually almost lock step with TMO. I forgot to mention this also includes the September Security Update.
    • 417.55 MB September security update just downloaded here for S24+ unlocked   Edit:  after Sept security update install, checked and found a 13MB GP System update as well.  Still showing August 1st there however. 
    • T-Mobile is selling the rest of the 3.45GHz spectrum to Columbia Capital.  
    • Still nothing for my AT&T and Visible phones.
  • Recently Browsing

    • No registered users viewing this page.
×
×
  • Create New...