Jump to content

Other Carriers and RRUs


Recommended Posts

I know I've heard mention that Verizon was going back and installing RRUs in some markets, other than that I was under the impression that Sprint/Clearwire was the only ones so far installing RRUs mounted up with the panel.

 

I was out checking towers for upgrades last night and found these panels with what looks like RRUs installed behind them. They don't look like the Samsung equipment Sprint is installing. Anyone have any guesses on whose they are?

IMG_5818CR2.jpg

 

IMG_5820CR2.jpg

 

Also where i took these pictures they are re-painting the water tower, they have setup a temporary tower but it only has 1 set of panels on it (there are multiple carriers on the water tower), can anyone tell whose they are?

IMG_5821CR2.jpg

 

and just for fun here is a pic of one of the Clearwire WiMax protection sites around here :)

IMG_5823CR2.jpg

 

Link to comment
Share on other sites

thanks for the replies, that would be the first tmobile gear i've seen with RRU's, does that mean they have LTE on that tower?

 

any ideas on the panels on the "temp" tower?

Link to comment
Share on other sites

thanks for the replies, that would be the first tmobile gear i've seen with RRU's, does that mean they have LTE on that tower?

 

any ideas on the panels on the "temp" tower?

 

T-mobile is deploying Ericsson RRU04's,RRU11's, and RRU12s which are the same  RRUs as Sprint / Tmobile / ATT with their old antennas. 

Link to comment
Share on other sites

I know I've heard mention that Verizon was going back and installing RRUs in some markets, other than that I was under the impression that Sprint/Clearwire was the only ones so far installing RRUs mounted up with the panel.

 

I was out checking towers for upgrades last night and found these panels with what looks like RRUs installed behind them. They don't look like the Samsung equipment Sprint is installing. Anyone have any guesses on whose they are?

 

 

 

 

Also where i took these pictures they are re-painting the water tower, they have setup a temporary tower but it only has 1 set of panels on it (there are multiple carriers on the water tower), can anyone tell whose they are?

 

 

and just for fun here is a pic of one of the Clearwire WiMax protection sites around here :)

 

 

Those little boxes are too small to be RRUs.  I bet those are diplexers.  Two bands are diplexed at the bottom of the site into one cable, then diplexed out again at the top back to two cables for each side of the antenna.

  • Like 1
Link to comment
Share on other sites

Here's a cool video of new panels being out up, thought I'd share. These guys seem to work well. http://youtu.be/asp5nzKB8F8

 

Can't say that I've seen anyone eyeball the azimuth from the ground...  no wonder why many of these sites are messed up.  There's a reason why the RF engineer wants the antenna pointed at 30 degrees and not 25 degrees.  Impossible to eyeball.

Link to comment
Share on other sites

Can't say that I've seen anyone eyeball the azimuth from the ground... no wonder why many of these sites are messed up. There's a reason why the RF engineer wants the antenna pointed at 30 degrees and not 25 degrees. Impossible to eyeball.

I was thinking the exact same thing. Eyeing the azimuth from 200' up?? That can't be precise. No wonder a lot of these installs are botched and have to be re-adjusted. Wow.

 

Don't get me wrong though, I have a very healthy respect for what those tower workers do and how dangerous it is for them.

 

At least those guys are safety tied most of the time.

 

Unlike these guys!!!!!

 

 

 

 

Sent from my Sprint iPhone 5, not the old one (using Tapatalk 2).

 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • large.unreadcontent.png.6ef00db54e758d06

  • gallery_1_23_9202.png

  • Posts

    • Since this is kind of the general chat thread, I have to share this humorous story (at least it is to me): Since around February/March of this year, my S22U has been an absolute pain to charge. USB-C cables would immediately fall out and it progressively got worse and worse until it often took me a number of minutes to get the angle of the cable juuuussst right to get charging to occur at all (not exaggerating). The connection was so weak that even walking heavily could cause the cable to disconnect. I tried cleaning out the port with a stable, a paperclip, etc. Some dust/lint/dirt came out but the connection didn't improve one bit. Needless to say, this was a MONSTER headache and had me hating this phone. I just didn't have the finances right now for a replacement.  Which brings us to the night before last. I am angry as hell because I had spent five minutes trying to get this phone to charge and failed. I am looking in the port and I notice it doesn't look right. The walls look rough and, using a staple, the back and walls feel REALLY rough and very hard. I get some lint/dust out with the staple and it improves charging in the sense I can get it to charge but it doesn't remove any of the hard stuff. It's late and it's charging, so that's enough for now. I decide it's time to see if that hard stuff is part of the connector or not. More aggressive methods are needed! I work in a biochem lab and we have a lot of different sizes of disposable needles available. So, yesterday morning, while in the lab I grab a few different sizes of needles between 26AWG and 31 AWG. When I got home, I got to work and start probing the connector with the 26 AWG and 31 AWG needle. The stuff feels extremely hard, almost like it was part of the connector, but a bit does break off. Under examination of the bit, it's almost sandy with dust/lint embedded in it. It's not part of the connector but instead some sort of rock-hard crap! That's when I remember that I had done some rock hounding at the end of last year and in January. This involved lots of digging in very sandy/dusty soils; soils which bare more than a passing resemblance to the crap in the connector. We have our answer, this debris is basically compacted/cemented rock dust. Over time, moisture in the area combined with the compression from inserting the USB-C connector had turned it into cement. I start going nuts chiseling away at it with the 26 AWG needle. After about 5-10 minutes of constant chiseling and scraping with the 26AWG and 31AWG needles, I see the first signs of metal at the back of the connector. So it is metal around the outsides! Another 5 minutes of work and I have scraped away pretty much all of the crap in the connector. A few finishing passes with the 31AWG needle, a blast of compressed air, and it is time to see if this helped any. I plug my regular USB-C cable and holy crap it clicks into place; it hasn't done that since February! I pick up the phone and the cable has actually latched! The connector works pretty much like it did over a year ago, it's almost like having a brand new phone!
    • That's odd, they are usually almost lock step with TMO. I forgot to mention this also includes the September Security Update.
    • 417.55 MB September security update just downloaded here for S24+ unlocked   Edit:  after Sept security update install, checked and found a 13MB GP System update as well.  Still showing August 1st there however. 
    • T-Mobile is selling the rest of the 3.45GHz spectrum to Columbia Capital.  
    • Still nothing for my AT&T and Visible phones.
  • Recently Browsing

    • No registered users viewing this page.
×
×
  • Create New...