Jump to content

CDMA 800 Testing PRL


Recommended Posts

I may have gotten something from L.A. but I can't upload the screenshot from Tapatalk.

 

Sent from my PG86100 using Tapatalk

 

Hit the little camera on your message reply. Pick gallery. Pick the picture. Pick tapatalk hosted. Works great here.

 

 

  • Like 1
Link to comment
Share on other sites

I'll upload it later. I'll just leave this here for the moment: Band# CDMA Cellular, CH# 476 and SID# 22429.

 

Sent from my PG86100 using Tapatalk

 

Rai, you did find me a protection site once. Did you come through with another first discovery???

 

I'm waiting with baited breath!!!! :azn:

 

Robert

Link to comment
Share on other sites

I'm glad to know the PRL works properly on phones equipped for Band Class 10-- though the band should be reported as "CDMA Cellular 2nd", but who knows how the firmware for the radio is configured! The PRL scan will ALWAYS prioritize the ESMR 1x carrier over your native PCS 1x carrier, but the EVDO (3G) association will always use your native PCS carriers. Please note that use of this PRL will likely cause increased battery draw since the phone will periodically scan for ESMR 1x carriers as a preferred link even if you have a great signal on your PCS 1x carrier. If you'd like to have any functionality changed, please let me know... I can disable EVDO upon ESMR 1x acquisition if you want that. I made it this way so that you can still use your phone normally and let it scan for ESMR carriers in the background.

  • Like 1
Link to comment
Share on other sites

What app is this that tells you the channel that you are using?

 

Band Class 1 is PCS (1900 MHz)... every band class has its own channel numbering scheme.

 

FYI..

For band class 1 (PCS)-- A block starts at 1850 MHz with channel 0... the spacing is 50 kHz per channel and the downlink frequency is 80 MHz higher than the uplink. The first usable CDMA channel is 25, then 50, 75, etc.

For band class 10 (ESMR) -- Channel 0 is 806 MHz... every channel is 25 kHz wide and the downlink is 45 MHz higher than the uplink. The first usable channel (to Sprint handsets as FCC approved) is centered at 817.9 MHz, which is 476, then 526, and 576 and 626. 676 would only be usable with allowances made by the area's cellular A side (band class 0) carrier.

I would go into band class 0 (cellular), but I've had too much wine-- there are two different channel numbering schemes and CDMA carriers in this band are 1.23 MHz wide rather than 1.25 MHz in all other band classes... you'll only see this band class when roaming on Verizon or Cellular South, so don't worry about it.

  • Like 2
Link to comment
Share on other sites

Edit: Now Tapatalk uploads the picture (Finally)

 

42574518-6a30-66f0.jpg

You're on the FAR edge of that cell-- you must be 5 miles from that tower! Signal is weak, but you're on ESMR. Service Option 0 may mean you're not actually in service... The big question is whether your forward link is set to RC-11, which would indicate 1xAdvanced versus 1xRTT, which would be RC-3.

Link to comment
Share on other sites

Edit: Now Tapatalk uploads the picture (Finally)

 

42574518-6a30-66f0.jpg

 

Channel 476? That is an ESMR band and it's in Riverside? Wow. Sprint is moving fast in some areas!

Link to comment
Share on other sites

You're on the FAR edge of that cell-- you must be 5 miles from that tower! Signal is weak, but you're on ESMR. Service Option 0 may mean you're not actually in service... The big question is whether your forward link is set to RC-11, which would indicate 1xAdvanced versus 1xRTT, which would be RC-3.

Well I was in the freeway when I screenshot it (wasn't driving though). The weak signal does explain why it kept changing from CDMA cellular to CDMA PCS.

 

Sent from my PG86100 using Tapatalk

Edited by UndeadNexus
Link to comment
Share on other sites

Well I was in the freeway when I screenshot it (wasn't driving though). The band# did flicker from CDMA cellular to CDMA PCS.

 

Sent from my PG86100 using Tapatalk

yeah-- the PRL should jump to the standard PCS scan if it loses the ESMR signal (goes below -113 dBm)... but it will ALWAYS search for the ESMR carrier first and constantly-- even if it has a good PCS carrier signal. You should be seeing significantly lower battery life-- SORRY!

Link to comment
Share on other sites

yeah-- the PRL should jump to the standard PCS scan if it loses the ESMR signal (goes below -113 dBm)... but it will ALWAYS search for the ESMR carrier first and constantly-- even if it has a good PCS carrier signal. You should be seeing significantly lower battery life-- SORRY!

That's ok. I can switch back to my old prl anytime. Forgot to mention that I saw some engineers working on a tower near the freeway in downtown L.A. I don't know if it was a Sprint tower though.

 

Sent from my PG86100 using Tapatalk

Link to comment
Share on other sites

Channel 476? That is an ESMR band and it's in Riverside? Wow. Sprint is moving fast in some areas!

Actually, this was from downtown L.A. Riverside's still on 1xRTT (for now).

 

Sent from my PG86100 using Tapatalk

Edited by UndeadNexus
Link to comment
Share on other sites

Actually, that was from downtown L.A. Riverside's still on 1xRTT (for now).

 

Sent from my PG86100 using Tapatalk

 

Downtown LA? Even more surprising.

Thanks for sharing

Link to comment
Share on other sites

I'm waiting with baited breath!!!!

 

Robert, have you been eating bait? Eww! And, judging from another thread, eating that bait has not only given you bad breath but also grown hair on your brain.

 

;)

 

AJ

Link to comment
Share on other sites

 

Robert, have you been eating bait? Eww! And, judging from another thread, eating that bait has not only given you bad breath but also grown hair on your brain.

 

 

 

AJ

XD hahaha

 

Sent from my PG86100 using Tapatalk

Link to comment
Share on other sites

It would have to be in LA. There is active deployment going on Downtown, the 110 Corridor, Hollywood and San Fernando. There is no activity in the Riverside market yet.

 

Robert - Posted from my E4GT with ICS using Forum Runner

Link to comment
Share on other sites

Was it determined that the Evo cannot lock to the G block? Which block would channel 725, band class 1, band # CDMA PCS be?

Are you talking about the EVO 4G or EVO 3D?

 

Sent from my PG86100 using Tapatalk

Link to comment
Share on other sites

Was it determined that the Evo cannot lock to the G block? Which block would channel 725, band class 1, band # CDMA PCS be?

 

PCS 0725 is the first full CDMA1X channel assignment in the PCS D block, which is one of two PCS A-F licenses (the PCS E block is the other) that Sprint holds in Chicago.

 

When I was last in Chicago a few months ago, PCS 0325 and 0725 were the two EV-DO carriers that I encountered, while PCS 0350, 0375, and 0775 were the three 1X carriers that I spotted. So, I suspect that your PCS 0725 is an EV-DO carrier.

 

AJ

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • large.unreadcontent.png.6ef00db54e758d06

  • gallery_1_23_9202.png

  • Posts

    • Since this is kind of the general chat thread, I have to share this humorous story (at least it is to me): Since around February/March of this year, my S22U has been an absolute pain to charge. USB-C cables would immediately fall out and it progressively got worse and worse until it often took me a number of minutes to get the angle of the cable juuuussst right to get charging to occur at all (not exaggerating). The connection was so weak that even walking heavily could cause the cable to disconnect. I tried cleaning out the port with a stable, a paperclip, etc. Some dust/lint/dirt came out but the connection didn't improve one bit. Needless to say, this was a MONSTER headache and had me hating this phone. I just didn't have the finances right now for a replacement.  Which brings us to the night before last. I am angry as hell because I had spent five minutes trying to get this phone to charge and failed. I am looking in the port and I notice it doesn't look right. The walls look rough and, using a staple, the back and walls feel REALLY rough and very hard. I get some lint/dust out with the staple and it improves charging in the sense I can get it to charge but it doesn't remove any of the hard stuff. It's late and it's charging, so that's enough for now. I decide it's time to see if that hard stuff is part of the connector or not. More aggressive methods are needed! I work in a biochem lab and we have a lot of different sizes of disposable needles available. So, yesterday morning, while in the lab I grab a few different sizes of needles between 26AWG and 31 AWG. When I got home, I got to work and start probing the connector with the 26 AWG and 31 AWG needle. The stuff feels extremely hard, almost like it was part of the connector, but a bit does break off. Under examination of the bit, it's almost sandy with dust/lint embedded in it. It's not part of the connector but instead some sort of rock-hard crap! That's when I remember that I had done some rock hounding at the end of last year and in January. This involved lots of digging in very sandy/dusty soils; soils which bare more than a passing resemblance to the crap in the connector. We have our answer, this debris is basically compacted/cemented rock dust. Over time, moisture in the area combined with the compression from inserting the USB-C connector had turned it into cement. I start going nuts chiseling away at it with the 26 AWG needle. After about 5-10 minutes of constant chiseling and scraping with the 26AWG and 31AWG needles, I see the first signs of metal at the back of the connector. So it is metal around the outsides! Another 5 minutes of work and I have scraped away pretty much all of the crap in the connector. A few finishing passes with the 31AWG needle, a blast of compressed air, and it is time to see if this helped any. I plug my regular USB-C cable and holy crap it clicks into place; it hasn't done that since February! I pick up the phone and the cable has actually latched! The connector works pretty much like it did over a year ago, it's almost like having a brand new phone!
    • That's odd, they are usually almost lock step with TMO. I forgot to mention this also includes the September Security Update.
    • 417.55 MB September security update just downloaded here for S24+ unlocked   Edit:  after Sept security update install, checked and found a 13MB GP System update as well.  Still showing August 1st there however. 
    • T-Mobile is selling the rest of the 3.45GHz spectrum to Columbia Capital.  
    • Still nothing for my AT&T and Visible phones.
  • Recently Browsing

    • No registered users viewing this page.
×
×
  • Create New...