Jump to content

Router Issues


centermedic

Recommended Posts

So, I'm thinking that my router is going bad. Here are my issues:

 

1) My internet connection seems sluggish even though the speedtest come back with my usual 4/mbps. Just to make sure it was not my computer I timed a 1300 mb download on my PS3. It took one hour with no other load on my connection.

 

2) I have noticed that sometimes the router allows certain devices to become bandwidth whores while bringing other devices to a standstill. 

 

Does this sound like a router issue to you guys?

Link to comment
Share on other sites

It could be several things. Is the software to the router up to date. You might unplug it if its up to date or reset it. Also check your network settings and see if anything is off.

 

Sent from my Sprint Galaxy S4 using Tapatalk 2

 

 

Link to comment
Share on other sites

PlayStation for me always takes an outrageous amount of time to download. Have you tested your speeds on other devices?

 

Same here, on WiFi. As soon as I wired it up, speeds shot through the roof to where they should be. No other device has an issue with speeds on my setup over WiFi.

 

Fat PS3 3rd Gen (no backwards compatibility). Buffalo WZR-HP-G300NH router.

 

 

Try a different browser you didn't have previously installed (Firefox, Chrome, Opera, etc.) that way you take a preinstalled browser having issues out of the equation. If possible, try using a different computer, not a phone or console. I'd recommend power cycling the router AND modem if you haven't already. If that doesn't change anything, try a factory reset on the router settings, perhaps something got messed up. Call your ISP if it is their modem/router/gateway. If you have a gateway, get rid of that stupid thing, they all suck. A separate modem/router always has worked better in my experience than a combined gateway.

Link to comment
Share on other sites

I bought a Netgear R6300 TOL AC router in March while also switching to Comcast 50/10 tier and had pings around 10-15 MS all the time and very fast web page loading. After a month pages got slightly laggy and speedtests showed a 20-25 MS ping.

 

I bought an Asus RT-AC66U router (their TOL AC router) and put it in and latency dropped back to what it was supposed to be and things started loading much snappier again.

 

So the router can be a cause. Have you wired your problem device straight to the modem yet? That was how I confirmed it was my router. 

 

Also with the RT-AC66U wifi performance is pretty much the same as a wired connection, by far the the best wifi router I've used to date. It has amazing range too. 

Link to comment
Share on other sites

I don't have the AC version of that Asus, just the 66u and this thing with Shibby's firmware is down right amazing. Vpn, ad blocking, multi ssid, vlan, ftp, ssh tunnel, file storage, etc.. Oh and router. Highly recommend the router.

  • Like 2
Link to comment
Share on other sites

Lets see:

 

I have power cycled the router and modem.

I use speedtest.net for my speed test.

The problem persists across three computers, desktop, windows 7, laptop windows vista and a chromebook

I will check to make sure the firmware is up to date and I will also try connecting directly to the router to see what happens then. Thanks for the suggestions!

Link to comment
Share on other sites

You can throw the fastest and best router at anything but if you have ISP issues its all for moot.

 

Reduce things down to the simplest form  and work up from there.

 

In all the years all my issues have been ISP related.

 

i run mid grade older routers Dlink DIR-825  for the dual band and gigabit switch ports.

 

I have 3, yes 3 of these linked together to provide decent coverage over my 2 story Brick house. if you can run aftermarket software such as DD-WRT I would recommend that as well.  

 

Unless your running internal  gigabit file servers you don't need the most expensive router out there. Your ISP will always be your bottleneck

Link to comment
Share on other sites

I don't have the AC version of that Asus, just the 66u and this thing with Shibby's firmware is down right amazing. Vpn, ad blocking, multi ssid, vlan, ftp, ssh tunnel, file storage, etc.. Oh and router. Highly recommend the router.

The RT-N66U is an excellent router as well, almost got it then saw the AC version on sale for just 20 more and got that.

 

I dabbled in DD-WRT and Tomato and found no real benefit for it at home just yet. It is nice to finally know how to set up and use tomato and dd-wrt though.

 

I'm happy with the stock firmware on the Asus for now, although I do have Merlin flashed on there which is just stock with extra features enabled.

Link to comment
Share on other sites

You can throw the fastest and best router at anything but if you have ISP issues its all for moot.

 

Reduce things down to the simplest form  and work up from there.

 

In all the years all my issues have been ISP related.

 

i run mid grade older routers Dlink DIR-825  for the dual band and gigabit switch ports.

 

I have 3, yes 3 of these linked together to provide decent coverage over my 2 story Brick house. if you can run aftermarket software such as DD-WRT I would recommend that as well.  

 

Unless your running internal  gigabit file servers you don't need the most expensive router out there. Your ISP will always be your bottleneck

My speedtest almost always show that I am getting the advertised speed. I assumed that cleared the ISP as the issue.

Link to comment
Share on other sites

So, I'm thinking that my router is going bad. Here are my issues:

 

1) My internet connection seems sluggish even though the speedtest come back with my usual 4/mbps. Just to make sure it was not my computer I timed a 1300 mb download on my PS3. It took one hour with no other load on my connection.

 

2) I have noticed that sometimes the router allows certain devices to become bandwidth whores while bringing other devices to a standstill. 

 

Does this sound like a router issue to you guys?

 

Unplugg the router from the cable modem and connect PC directly to cable modem. Run speed test etc. If this works fine then you can probably say is the router.

 

You can also try a factory reset on the unit.

 

Your cable modem can also have gone bad.

 

@l3x

Link to comment
Share on other sites

I don't have the AC version of that Asus, just the 66u and this thing with Shibby's firmware is down right amazing. Vpn, ad blocking, multi ssid, vlan, ftp, ssh tunnel, file storage, etc.. Oh and router. Highly recommend the router.

I have the same router. Out of all the routers I have had, this thing just rocks. Most impressed I have ever been. Did I say this thing rocks!

 

Sent from my SPH-L710 using Tapatalk 2

 

 

Link to comment
Share on other sites

  • 2 weeks later...

Everything checks out on the router. As i was trying to think about what else could be causing my data slowdown I remembered how many new ssid's I can pull up when I do a wifi search. Then it occurred to me, my router is 2.4 ghz only!

Link to comment
Share on other sites

  • 2 weeks later...

Ok. So I got a dual band router g/n 2.4/5. Moved whatever was compatible to 5 ghz. I also took a look at the 2.4 spectrum and holy crap!. There are seven other 2.4 connections(all wireless-n, go figure) in my immediate area. I switched the channel from 11 down to 1 as that was the least congested range. So far it seems better.

Link to comment
Share on other sites

Ok. So I got a dual band router g/n 2.4/5. Moved whatever was compatible to 5 ghz. I also took a look at the 2.4 spectrum and holy crap!. There are seven other 2.4 connections(all wireless-n, go figure) in my immediate area. I switched the channel from 11 down to 1 as that was the least congested range. So far it seems better.

 

Ideally you want to be as far away from others as possible. So 1 and 11 are the best options if available (you only have people on one side of you in the spectrum range). If those aren't available then as far away as others as you can.

 

Around me I have 4 access points. One at 1, 6, 8, 11... so I set myself up at channel 4 and bumped it up to 40MHz spectrum on my 2.4GHz-only N-router. I know for a fact my router has the highest power output of any of these routers (they are basic consumer grade Linksys, Netgear, and Qwest routers judging by SSIDs and are likely to be using default settings knowing my neighbors, at least they setup security right?). In addition, our houses are far enough apart that while the signal is visible, they aren't really usable from my place.

 

I have aimed my router's two bi-directional antennae down my house (it sits in a corner of the building) to get maximum signal at the other end of my place (200ft, brick and drywall) and still getting 60-80% signal strength depending on the device at the other end. On my neighbor's properties, the signal is visible and usable but would easily be overcome by a router on their property without causing interference where it would realistically be used.

 

In addition, by bumping up to 40MHz spectrum usage I nearly doubled my WiFi speeds on most of my equipment.  :D When you know what you're doing you can optimize pretty well. I've considered going around the neighborhood scanning WiFi and mapping out a rough setup to determine the most spectrum-efficient channeling and seeing if they're interested. Mutual improvement, and they know I do this kind of thing anyway, probably wouldn't be hard to convince people. I just haven't been that bored.  :lol:

  • Like 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • large.unreadcontent.png.6ef00db54e758d06

  • gallery_1_23_9202.png

  • Posts

    • Since this is kind of the general chat thread, I have to share this humorous story (at least it is to me): Since around February/March of this year, my S22U has been an absolute pain to charge. USB-C cables would immediately fall out and it progressively got worse and worse until it often took me a number of minutes to get the angle of the cable juuuussst right to get charging to occur at all (not exaggerating). The connection was so weak that even walking heavily could cause the cable to disconnect. I tried cleaning out the port with a stable, a paperclip, etc. Some dust/lint/dirt came out but the connection didn't improve one bit. Needless to say, this was a MONSTER headache and had me hating this phone. I just didn't have the finances right now for a replacement.  Which brings us to the night before last. I am angry as hell because I had spent five minutes trying to get this phone to charge and failed. I am looking in the port and I notice it doesn't look right. The walls look rough and, using a staple, the back and walls feel REALLY rough and very hard. I get some lint/dust out with the staple and it improves charging in the sense I can get it to charge but it doesn't remove any of the hard stuff. It's late and it's charging, so that's enough for now. I decide it's time to see if that hard stuff is part of the connector or not. More aggressive methods are needed! I work in a biochem lab and we have a lot of different sizes of disposable needles available. So, yesterday morning, while in the lab I grab a few different sizes of needles between 26AWG and 31 AWG. When I got home, I got to work and start probing the connector with the 26 AWG and 31 AWG needle. The stuff feels extremely hard, almost like it was part of the connector, but a bit does break off. Under examination of the bit, it's almost sandy with dust/lint embedded in it. It's not part of the connector but instead some sort of rock-hard crap! That's when I remember that I had done some rock hounding at the end of last year and in January. This involved lots of digging in very sandy/dusty soils; soils which bare more than a passing resemblance to the crap in the connector. We have our answer, this debris is basically compacted/cemented rock dust. Over time, moisture in the area combined with the compression from inserting the USB-C connector had turned it into cement. I start going nuts chiseling away at it with the 26 AWG needle. After about 5-10 minutes of constant chiseling and scraping with the 26AWG and 31AWG needles, I see the first signs of metal at the back of the connector. So it is metal around the outsides! Another 5 minutes of work and I have scraped away pretty much all of the crap in the connector. A few finishing passes with the 31AWG needle, a blast of compressed air, and it is time to see if this helped any. I plug my regular USB-C cable and holy crap it clicks into place; it hasn't done that since February! I pick up the phone and the cable has actually latched! The connector works pretty much like it did over a year ago, it's almost like having a brand new phone!
    • That's odd, they are usually almost lock step with TMO. I forgot to mention this also includes the September Security Update.
    • 417.55 MB September security update just downloaded here for S24+ unlocked   Edit:  after Sept security update install, checked and found a 13MB GP System update as well.  Still showing August 1st there however. 
    • T-Mobile is selling the rest of the 3.45GHz spectrum to Columbia Capital.  
    • Still nothing for my AT&T and Visible phones.
  • Recently Browsing

    • No registered users viewing this page.
×
×
  • Create New...