Jump to content

Old Clear gear


mhammett

Recommended Posts

Some of their backhaul radios may be retained by Sprint.

 

You should also know that most designs they use run in licensed bands.  As such, it is not legal to sell them to someone who is not FCC licensed.  Additionally, even if you could purchase them, it would be a combination of illegal and irresponsible to attempt to install/operate them without registration and approval with the FCC.  Improper installation could cause serious interference issues, and they ARE pretty good at tracking that stuff down, especially when you're interfering with either a telecom's equipment or somebody's high dollar corporate radio WAN links.

 

You might look into a product called Air Fiber from Ubiquiti.  Most of those models can operate in unlicensed bands, are designed to be easier to set up, and are moderately inexpensive.  A couple of thousand dollars can have you a 2000-5000 meter gigabit link if you have line of sight.

 

Dragonwave makes a few unlicensed products as well, though their hardware tends to be more carrier-centric and more complicated to install.  I would consider their hardware to be more robust and reliable, though it is more expensive.

  • Like 1
Link to comment
Share on other sites

O P is an ISP, and is quite knowledgeable about FCC requirements.

Didn't know that.

 

The OP wants the backhaul gear, not the endpoint gear. That means he wants the microwave P2P transmission gear.

I did understand that. I was talking about the microwave backhaul hardware.
Link to comment
Share on other sites

I know where to purchase the gear new as I have a whole list of vendors. I'm expecting that pulling thousands or tens of thousands of predominantly Dragonwave radios that I could make good use of. Most of their existing links will not sustain TDD-LTE as Sprint is implementing it. I'm actually soon implementing a Dragonwave network for a client.

 

Licensing and coordination is pretty easy, you just need to do it.

 

I know several 2.5 GHz license holders that would love to get their WiMax gear, whenever it is pulled.

 

I beta test Ubiquiti hardware, so I'm familiar with their offering.

 

I am also aware that you were not aware of my credentials when I posted.

 

Sent from my EVO using Tapatalk

 

 

Link to comment
Share on other sites

...

 

Licensing and coordination is pretty easy, you just need to do it.

 

...

 

FCC is easy, just paperwork and waiting.

 

Problem is that there are too many people who would "play" with this hardware without knowing (or often without caring about) the potential implications. They might not know what we do, being both in the telecommunications industry, but still know enough to make it work (or at least cause enough trouble attempting to do so).

 

I read some of ARRL's copies of FCC enforcement actions. It's really quite amusing to see the amount of havoc one can cause with a simple MF, HF, or VHF rig at a couple hundred Watts.

  • Like 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • large.unreadcontent.png.6ef00db54e758d06

  • gallery_1_23_9202.png

  • Posts

    • Since this is kind of the general chat thread, I have to share this humorous story (at least it is to me): Since around February/March of this year, my S22U has been an absolute pain to charge. USB-C cables would immediately fall out and it progressively got worse and worse until it often took me a number of minutes to get the angle of the cable juuuussst right to get charging to occur at all (not exaggerating). The connection was so weak that even walking heavily could cause the cable to disconnect. I tried cleaning out the port with a stable, a paperclip, etc. Some dust/lint/dirt came out but the connection didn't improve one bit. Needless to say, this was a MONSTER headache and had me hating this phone. I just didn't have the finances right now for a replacement.  Which brings us to the night before last. I am angry as hell because I had spent five minutes trying to get this phone to charge and failed. I am looking in the port and I notice it doesn't look right. The walls look rough and, using a staple, the back and walls feel REALLY rough and very hard. I get some lint/dust out with the staple and it improves charging in the sense I can get it to charge but it doesn't remove any of the hard stuff. It's late and it's charging, so that's enough for now. I decide it's time to see if that hard stuff is part of the connector or not. More aggressive methods are needed! I work in a biochem lab and we have a lot of different sizes of disposable needles available. So, yesterday morning, while in the lab I grab a few different sizes of needles between 26AWG and 31 AWG. When I got home, I got to work and start probing the connector with the 26 AWG and 31 AWG needle. The stuff feels extremely hard, almost like it was part of the connector, but a bit does break off. Under examination of the bit, it's almost sandy with dust/lint embedded in it. It's not part of the connector but instead some sort of rock-hard crap! That's when I remember that I had done some rock hounding at the end of last year and in January. This involved lots of digging in very sandy/dusty soils; soils which bare more than a passing resemblance to the crap in the connector. We have our answer, this debris is basically compacted/cemented rock dust. Over time, moisture in the area combined with the compression from inserting the USB-C connector had turned it into cement. I start going nuts chiseling away at it with the 26 AWG needle. After about 5-10 minutes of constant chiseling and scraping with the 26AWG and 31AWG needles, I see the first signs of metal at the back of the connector. So it is metal around the outsides! Another 5 minutes of work and I have scraped away pretty much all of the crap in the connector. A few finishing passes with the 31AWG needle, a blast of compressed air, and it is time to see if this helped any. I plug my regular USB-C cable and holy crap it clicks into place; it hasn't done that since February! I pick up the phone and the cable has actually latched! The connector works pretty much like it did over a year ago, it's almost like having a brand new phone!
    • That's odd, they are usually almost lock step with TMO. I forgot to mention this also includes the September Security Update.
    • 417.55 MB September security update just downloaded here for S24+ unlocked   Edit:  after Sept security update install, checked and found a 13MB GP System update as well.  Still showing August 1st there however. 
    • T-Mobile is selling the rest of the 3.45GHz spectrum to Columbia Capital.  
    • Still nothing for my AT&T and Visible phones.
  • Recently Browsing

    • No registered users viewing this page.
×
×
  • Create New...