Jump to content

Comparison of LTE vs. Current 3G coverage


Recommended Posts

I'm sure someone will be able to answer this for me and know that I'm not asking for an apples to apples comparison just what others have seen from thier experience or what they think. Right now I have a terrible signal inside my job. Recently it has got so bad that either my radio is disconnected or it's 1X. This maybe a result of ongoing deployment, but either way it has always been bad here. When the deployment is completed should I see slightly better coverage inside, worse, or the same.

 

Especially if you are going thru deployment now I would like to know what your experience is.

Link to comment
Share on other sites

I had a similar issue at my work, its like working inside a lead box. With the tower I connect to being less than 1 mile away, I was continuously around -98 to -110 dBm in signal stregth. When the tower was updated, I saw a VERY SLIGHT improvement, not in bars or signal strength, but in the fact that all my calls were clearer inside the building, everyone I was talking to didn't sound like a robot, and I didn't have the "oh you have a voicemail, but your phone didn't ring" problem I used to have before the tower by my work was upgraded.

 

Now keep in mind, every situation is different and my experience may not be the same for you.

Link to comment
Share on other sites

LTE-1900 will be worse than current 3g 1900. 3g 1900 will be improved by up to ~20%, however. If you get a new phone that has LTE-800 and the towers close to you are outputting LTE-800, then your in building LTE coverage could be better by a lot or a little than current 3g. LTE-800 is theory right now so we would have to go by similar deployments like Verizon LTE-700, which doesn't travel as far as their CDMA/3g 850, but does travel quite well.

  • Like 1
Link to comment
Share on other sites

I had a similar issue at my work, its like working inside a lead box. With the tower I connect to being less than 1 mile away, I was continuously around -98 to -110 dBm in signal stregth. When the tower was updated, I saw a VERY SLIGHT improvement, not in bars or signal strength, but in the fact that all my calls were clearer inside the building, everyone I was talking to didn't sound like a robot, and I didn't have the "oh you have a voicemail, but your phone didn't ring" problem I used to have before the tower by my work was upgraded.

 

Now keep in mind, every situation is different and my experience may not be the same for you.

Thanks that was exactly what I was looking for as an example.
Link to comment
Share on other sites

LTE-1900 will be worse than current 3g 1900. 3g 1900 will be improved by up to ~20%, however. If you get a new phone that has LTE-800 and the towers close to you are outputting LTE-800, then your in building LTE coverage could be better by a lot or a little than current 3g. LTE-800 is theory right now so we would have to go by similar deployments like Verizon LTE-700, which doesn't travel as far as their CDMA/3g 850, but does travel quite well.

Lost completely with your post..sorry :blink:

Link to comment
Share on other sites

ok

 

Coverage will probably be something like:

 

NV CDMA-1x 800 > NV CDMA-1xA 1900 > Legacy CDMA-1x 1900 >= NV LTE-800 >= NV EVDO 1900 > Legacy EVDO 1900 > LTE -1900

 

NV LTE-800 might not travel as far as NV/Legacy EVDO-1900, or might travel further than NV/Legacy CDMA 1X 1900, not sure.

 

Network Vision LTE-800 might be greater than EVDO currently is.

My thinking is like this in order of highest priority:

1. Lower frequency travels further

2. CDMA travels further than EVDO. EVDO travels further than LTE.

3. NV increases coverage with RRU + antenna improvements

  • Like 1
Link to comment
Share on other sites

LTE requires a stronger signal than EVDO or 1x to work, so it will have slightly worse coverage than 3G does now. However, during the network vision upgrades, Sprint is installing radio technology that will allow them to improve signal strength by up to 20% over their current deployment. Because of this, indoor coverage and performance should see a slight boost on any current Sprint phone after the upgrades.

 

Sometime after the initial upgrade, Sprint is then going to come through and enable 1x on the ESMR band, which is on a much lower frequency than their current PCS 1x. This will allow dramatically better in network coverage and signal strength. This will only affect 1x and will only work on phones released after the EVO 3D (sans iPhone 4 or 4S). Also, 1x only carries voice and 2G speed data, so 3G won't get any better after the initial upgrade.

 

Even further down the road, Sprint will deploy LTE on ESMR. Then, 4G will have better coverage than 3G by a significant margin. This will require new devices to access though.

Link to comment
Share on other sites

Even further down the road, Sprint will deploy LTE on ESMR. Then, 4G will have better coverage than 3G by a significant margin.

 

No, be careful with that prediction. LTE 800 may provide broader coverage than EV-DO 1900 does, but there is no guarantee. And "significant margin" is probably too strong.

 

AJ

Link to comment
Share on other sites

It might also be relevant to note that we might not see the complete NV boost in signal strength until downtilt is adjusted back to pre-NV levels. I have heard it mentioned several times on here that due to the incomplete nature of the build out to this point, that most panels have little downtilt, in an effort to maximize area covered. I don't know if any NV buildout is far enough along to have had the downtilt adjusted.

  • Like 1
Link to comment
Share on other sites

The panels have 3 separate downtilt adjustments. PCS EVDO/1X to mock the legacy network, 800SMR, and PCS LTE. If by some miracle, the tower crew fires up 3G when they fire up 4G. They would of course have to adjust the PCS EVDO/1X downtilt to be somewhat like the previous legacy equipment in order to prevent interference with adjacent legacy network cells. They can do whatever they want with the 800SMR and LTE downtilt adjustments of course.

 

Your voice and texting issues could probably be solved when your local site becomes 3G activated (meaning legacy is shut down) due to the newer panel and RRU benefit. But I bet it will really make a difference when 800SMR is activated in your area. It might possibly be activated right now with that goofy Utah SID or maybe even the Tampa SID. You'll have to test that 800SMR PRL with all SIDs activated to find out.

  • Like 1
Link to comment
Share on other sites

The panels have 3 separate downtilt adjustments. PCS EVDO/1X to mock the legacy network...

 

Are you mocking the legacy network?

 

AJ

  • Like 3
Link to comment
Share on other sites

The panels have 3 separate downtilt adjustments. PCS EVDO/1X to mock the legacy network, 800SMR, and PCS LTE. If by some miracle, the tower crew fires up 3G when they fire up 4G. They would of course have to adjust the PCS EVDO/1X downtilt to be somewhat like the previous legacy equipment in order to prevent interference with adjacent legacy network cells. They can do whatever they want with the 800SMR and LTE downtilt adjustments of course.

 

Your voice and texting issues could probably be solved when your local site becomes 3G activated (meaning legacy is shut down) due to the newer panel and RRU benefit. But I bet it will really make a difference when 800SMR is activated in your area. It might possibly be activated right now with that goofy Utah SID or maybe even the Tampa SID. You'll have to test that 800SMR PRL with all SIDs activated to find out.

 

Ah, good to know. I didn't know they had separate down-tilts for all 3.

Link to comment
Share on other sites

It might possibly be activated right now with that goofy Utah SID or maybe even the Tampa SID. You'll have to test that 800SMR PRL with all SIDs activated to find out.

 

Elaborate please...

 

800SMR is actually what I have been looking forward to the most.

Link to comment
Share on other sites

 

Elaborate please...

 

800SMR is actually what I have been looking forward to the most.

 

Look in the download section here. No LTE in that prl on qualcomm devices though.

 

-- "Sensorly or it didn't happen!"

 

 

Link to comment
Share on other sites

It deserves it. Its been mocking him for a longggg time.

 

"Hush, little baby, don't say a word, Mama's gonna buy you a mockingbird."

 

AJ

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • large.unreadcontent.png.6ef00db54e758d06

  • gallery_1_23_9202.png

  • Posts

    • Since this is kind of the general chat thread, I have to share this humorous story (at least it is to me): Since around February/March of this year, my S22U has been an absolute pain to charge. USB-C cables would immediately fall out and it progressively got worse and worse until it often took me a number of minutes to get the angle of the cable juuuussst right to get charging to occur at all (not exaggerating). The connection was so weak that even walking heavily could cause the cable to disconnect. I tried cleaning out the port with a stable, a paperclip, etc. Some dust/lint/dirt came out but the connection didn't improve one bit. Needless to say, this was a MONSTER headache and had me hating this phone. I just didn't have the finances right now for a replacement.  Which brings us to the night before last. I am angry as hell because I had spent five minutes trying to get this phone to charge and failed. I am looking in the port and I notice it doesn't look right. The walls look rough and, using a staple, the back and walls feel REALLY rough and very hard. I get some lint/dust out with the staple and it improves charging in the sense I can get it to charge but it doesn't remove any of the hard stuff. It's late and it's charging, so that's enough for now. I decide it's time to see if that hard stuff is part of the connector or not. More aggressive methods are needed! I work in a biochem lab and we have a lot of different sizes of disposable needles available. So, yesterday morning, while in the lab I grab a few different sizes of needles between 26AWG and 31 AWG. When I got home, I got to work and start probing the connector with the 26 AWG and 31 AWG needle. The stuff feels extremely hard, almost like it was part of the connector, but a bit does break off. Under examination of the bit, it's almost sandy with dust/lint embedded in it. It's not part of the connector but instead some sort of rock-hard crap! That's when I remember that I had done some rock hounding at the end of last year and in January. This involved lots of digging in very sandy/dusty soils; soils which bare more than a passing resemblance to the crap in the connector. We have our answer, this debris is basically compacted/cemented rock dust. Over time, moisture in the area combined with the compression from inserting the USB-C connector had turned it into cement. I start going nuts chiseling away at it with the 26 AWG needle. After about 5-10 minutes of constant chiseling and scraping with the 26AWG and 31AWG needles, I see the first signs of metal at the back of the connector. So it is metal around the outsides! Another 5 minutes of work and I have scraped away pretty much all of the crap in the connector. A few finishing passes with the 31AWG needle, a blast of compressed air, and it is time to see if this helped any. I plug my regular USB-C cable and holy crap it clicks into place; it hasn't done that since February! I pick up the phone and the cable has actually latched! The connector works pretty much like it did over a year ago, it's almost like having a brand new phone!
    • That's odd, they are usually almost lock step with TMO. I forgot to mention this also includes the September Security Update.
    • 417.55 MB September security update just downloaded here for S24+ unlocked   Edit:  after Sept security update install, checked and found a 13MB GP System update as well.  Still showing August 1st there however. 
    • T-Mobile is selling the rest of the 3.45GHz spectrum to Columbia Capital.  
    • Still nothing for my AT&T and Visible phones.
  • Recently Browsing

    • No registered users viewing this page.
×
×
  • Create New...