Jump to content

Severe Signal Interference


gopher_otis

Recommended Posts

I think something may be jamming the Sprint signal at the apartment complex I live in. I have hardly ever been able to use data there. I just noticed that when I step ten feet away from the building, my signal jumps into the -70's, but when I get closer, the signal stays about -95. These measurements are for voice, I know, but I can actually use data as long as I stay away from the building. Does anyone have and ideas as to why this is happening and what I can do to make it stop? Thanks in advance.

 

Sent via Forum Runner on my redsn0w iOS 5.1 iPhone 4 

Edited by gopher_otis
Link to comment
Share on other sites

Interference does not cause a decrease in RF signal strength. If a device measures just the intended signal, then interference causes no change in signal strength. On the other hand, if a device measures all of the RF in the particular channel, then interference causes an increase in field strength.

 

So, you seem to be experiencing severe RF fading, not interference.

 

AJ

Link to comment
Share on other sites

I use to live in a complex that was dead center of an "excellent" sprint signal area and less than a mile from a tower .... outside it was in the -80's, inside it was only usable next to the windows. I never could explain it, considering restaurants and buildings all around me got a signal fine while indoors.

Link to comment
Share on other sites

I use to live in a complex that was dead center of an "excellent" sprint signal area and less than a mile from a tower .... outside it was in the -80's, inside it was only usable next to the windows. I never could explain it, considering restaurants and buildings all around me got a signal fine while indoors.

 

A building of sufficient metallic construction can function much like a Faraday cage.

 

http://en.wikipedia.org/wiki/Faraday_cage

 

AJ

Link to comment
Share on other sites

Apartments are tough on Sprint's signal with all the obstructions.

I live on the second floor above most surrounding trees and buildings so I'm not sure what you mean by obstructions.

 

Fireproofing in apartments can cause lower signal strength.

While taking a look in the attic' date=' I didn't see any special type of fireproofing which is kind of funny because the landlord is a firefighter.

 

I use to live in a complex that was dead center of an "excellent" sprint signal area and less than a mile from a tower .... outside it was in the -80's, inside it was only usable next to the windows. I never could explain it, considering restaurants and buildings all around me got a signal fine while indoors.

There are two Sprint towers equally distant from where I live. Maybe my phone is constantly toggling between both of them?

 

A building of sufficient metallic construction can function much like a Faraday cage.

 

http://en.wikipedia.org/wiki/Faraday_cage

AJ

It's an older building with the exterior walls on the first floor being brick, the second floor and roof trusses being regular wooden ballon frame construction. While looking in the attic, I did notice that all the electrical wires have been run through metal tubing, which crisscrosses in every direction up there. Maybe these could be the Faraday cage?

 

 Sent via Forum Runner on my redsn0w iOS 5.1 iPhone 4 

Link to comment
Share on other sites

Apartments are built to commercial standards unlike homes. You have lots of metal conduit, water pipes, maybe a fire sprinkler system, thick fire walls between adjoining units,foil lined insulation, etc. I am no expert but apartments have always been a source of problem calls we get.

 

Homes with pretty metal roofs or radiant barriers are also becoming an issue.

 

How about getting a free Airave?

Link to comment
Share on other sites

How about getting a free Airave?

I don't have a home ISP.

 

Forgot to mention... my apartment was also full of fluorescent commercial style lighting... always seemed like the closer you were to them' date=' the worse the chances you got a signal[/quote']

I know there are two 4' fluorescent lights in every kitchen in the complex.

 

Do coated Low-E windows affect reception?

 

From what I read here I wouldn't be surprised if they did dampen the signal. http://en.m.wikipedia.org/wiki/Low_emissivity

 

 Sent via Forum Runner on my redsn0w iOS 5.1 iPhone 4 

Link to comment
Share on other sites

I work in construction management and LO-e glass (and worse is LO-e Squared glass) are horrible for RF transferrence. However, these are only used in high end commercial buildings and estate homes.

 

Here in New Mexico, we have a lot of adobe homes. Adobe homes are RF absorbing clay brick that's covered in "chicken wire" under a stucco base coat and finish coat. If the clay and Portland cement weren't enough, then the Faraday cages created by the lath wire does it in. I have been in adobes 500' from a tower and get no signal indoors.

 

Robert - Posted from my E4GT with ICS using Forum Runner

Link to comment
Share on other sites

Here in New Mexico, we have a lot of adobe homes. Adobe homes are RF absorbing clay brick that's covered in "chicken wire" under a stucco base coat and finish coat. If the clay and Portland cement weren't enough, then the Faraday cages created by the lath wire does it in. I have been in adobes 500' from a tower and get no signal indoors.

 

The in car coverage in New Mexico is just as bad.

 

 

AJ

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • large.unreadcontent.png.6ef00db54e758d06

  • gallery_1_23_9202.png

  • Posts

    • Since this is kind of the general chat thread, I have to share this humorous story (at least it is to me): Since around February/March of this year, my S22U has been an absolute pain to charge. USB-C cables would immediately fall out and it progressively got worse and worse until it often took me a number of minutes to get the angle of the cable juuuussst right to get charging to occur at all (not exaggerating). The connection was so weak that even walking heavily could cause the cable to disconnect. I tried cleaning out the port with a stable, a paperclip, etc. Some dust/lint/dirt came out but the connection didn't improve one bit. Needless to say, this was a MONSTER headache and had me hating this phone. I just didn't have the finances right now for a replacement.  Which brings us to the night before last. I am angry as hell because I had spent five minutes trying to get this phone to charge and failed. I am looking in the port and I notice it doesn't look right. The walls look rough and, using a staple, the back and walls feel REALLY rough and very hard. I get some lint/dust out with the staple and it improves charging in the sense I can get it to charge but it doesn't remove any of the hard stuff. It's late and it's charging, so that's enough for now. I decide it's time to see if that hard stuff is part of the connector or not. More aggressive methods are needed! I work in a biochem lab and we have a lot of different sizes of disposable needles available. So, yesterday morning, while in the lab I grab a few different sizes of needles between 26AWG and 31 AWG. When I got home, I got to work and start probing the connector with the 26 AWG and 31 AWG needle. The stuff feels extremely hard, almost like it was part of the connector, but a bit does break off. Under examination of the bit, it's almost sandy with dust/lint embedded in it. It's not part of the connector but instead some sort of rock-hard crap! That's when I remember that I had done some rock hounding at the end of last year and in January. This involved lots of digging in very sandy/dusty soils; soils which bare more than a passing resemblance to the crap in the connector. We have our answer, this debris is basically compacted/cemented rock dust. Over time, moisture in the area combined with the compression from inserting the USB-C connector had turned it into cement. I start going nuts chiseling away at it with the 26 AWG needle. After about 5-10 minutes of constant chiseling and scraping with the 26AWG and 31AWG needles, I see the first signs of metal at the back of the connector. So it is metal around the outsides! Another 5 minutes of work and I have scraped away pretty much all of the crap in the connector. A few finishing passes with the 31AWG needle, a blast of compressed air, and it is time to see if this helped any. I plug my regular USB-C cable and holy crap it clicks into place; it hasn't done that since February! I pick up the phone and the cable has actually latched! The connector works pretty much like it did over a year ago, it's almost like having a brand new phone!
    • That's odd, they are usually almost lock step with TMO. I forgot to mention this also includes the September Security Update.
    • 417.55 MB September security update just downloaded here for S24+ unlocked   Edit:  after Sept security update install, checked and found a 13MB GP System update as well.  Still showing August 1st there however. 
    • T-Mobile is selling the rest of the 3.45GHz spectrum to Columbia Capital.  
    • Still nothing for my AT&T and Visible phones.
  • Recently Browsing

    • No registered users viewing this page.
×
×
  • Create New...