Jump to content

Sprint Wifi Calling.....


runagun

Recommended Posts

I wish Sprint would drop the e911 requirements. T-mobile does wifi calling and you don't have to constantly be entering your location to use it.

 

Also any idea why wifi calling does not work in airplane mode with wifi enabled?

The more I think about it, the more dumb this e911 becomes. Why not just force a phone to go back to CDMA when someone dials 911 when using WiFi calling? It cant be that hard to make it happen.
Link to comment
Share on other sites

The more I think about it, the more dumb this e911 becomes. Why not just force a phone to go back to CDMA when someone dials 911 when using WiFi calling? It cant be that hard to make it happen.

It already does. http://support.sprint.com/support/article/FAQs_about_Sprint_WiFi_calling/173e331f-8423-453e-93cb-4688f6a91f67#!/. I would rather have the address info available if the macro network is not available when calling emergency services.

 

Do emergency services work with Wi-Fi Calling?

US / Puerto Rico / US Virgin Islands: 9-1-1 service through Wi-Fi Calling may not be available or may be limited compared to traditional 9-1-1 service due to circumstances including, but not limited to, relocation of equipment, internet congestion or connection failure, loss of electrical power, delays in availability of registered location information and/or other technical problems. A 9-1-1 call will first attempt to route over a wireless network. If a 9-1-1 call doesn’t route over a wireless network within approximately 20 seconds, a 9-1-1 call may then attempt to route over Wi-Fi Calling. Always be prepared to provide your precise location information to emergency service personnel and to contact emergency services by alternate means. 

Link to comment
Share on other sites

Funny, I don't have to change my E911 address to use wifi calling anywhere I want with my iPhone.

 

 

Sent from Josh's iPhone 6+ using Tapatalk

  • Like 1
Link to comment
Share on other sites

Anyone else having a problem with inbound calls labeled as either "No Caller ID" or "Unknown?" I disabled wifi calling when 8.3 came out due to not being able to make or receive calls but re-enabled it a few days ago and haven't had that specific issue but now all calls come in as essentially a blocked number, the same thing happens to a friend of mine.

Link to comment
Share on other sites

Anyone else having a problem with inbound calls labeled as either "No Caller ID" or "Unknown?" I disabled wifi calling when 8.3 came out due to not being able to make or receive calls but re-enabled it a few days ago and haven't had that specific issue but now all calls come in as essentially a blocked number, the same thing happens to a friend of mine.

Works fine on my Android phone.

Link to comment
Share on other sites

I'm sure that this has been asked before, but since the Nexus 6, on T-Mobile, will be getting WiFi calling...

 

Does anyone have any ideas as to when WiFi calling might be coming for the Sprint version of Nexus 6?

Link to comment
Share on other sites

Do wifi calls typically sound better or worse than standard cell calls (non-hd)?

About the same, maybe a little better than a non-hd call. I just wish you could connect as an HD call through wifi-calling. That would make it truly a great feature.

 

As a side note, my parents just took a vacation to VT, and picked a cabin in the middle of a huge hole of no service. I was able to talk my mom through setting up wifi calling on her phone (S4T) by calling the landline in her cabin. She was pretty excited to be able to have service where she otherwise wouldn't.

 

Sent from my Note 4.

  • Like 2
Link to comment
Share on other sites

Just got back from a trip to Italy and Nice/Monaco. WiFi calling worked great overseas and I was thoroughly impressed. We brought a MiFi device, and when we got to Italy, purchased a data only SIM card through Vodafone Italy. Once I connected via WiFi on my phone to the device, I was able to activate the WiFi calling feature. It doesn't ask for an address, but a message does pop up (screenshot attached) indicating you are in an international location and emergency services may not be available.

 

So I basically had cell service throughout our trip by remaining connected to the MiFi device. I was able to text and make phone calls to US based numbers, and they were able to call and text me. If I were to call a number in Italy, I believe international chargers would have applied, but I never needed to. If the device had a weak signal, the WiFi calling would disconnect, but would reconnect when the signal was strong again.

 

I also connected to WiFi calling with other WiFi connections throughout the trip (at our hotel, airbnb places, restaurants, and airports), and all worked flawlessly. It's a great service, especially if you travel internationally. You no longer need to buy a voice/data SIM card, just bring a MiFi device with you and purchase a data only SIM (ours was 30 euros for 10 gigs).

 

BTW, 3G is quite fast in Italy, as is 4G. Never did a speed test as we were trying to conserve our data limit, but we never experienced any slowness when the device was on 3G or 4G. Also, FYI, if you have an Android, Airplane mode needs to be off for WiFi calling to work.

Screenshot_2015-05-24-18-54-32.png

  • Like 6
Link to comment
Share on other sites

Did you try out the value roaming offered by sprint?!!? No cost texting and data!

 

I left on May 14th, and when I checked a few days prior to that, Italy wasn't included in the international value roaming. But apparently it was added on May 18th, per this article: http://www.eweek.com/mobile/sprint-expands-its-free-2g-data-roaming-to-7-more-nations.html

 

So no, I didn't use the roaming since I wasn't aware I could in Italy. But the WiFi calling worked just fine, and instead of 2G speeds, I got 3G and LTE speeds. My phone did connect to the 3 network there once or twice when I was off of Wifi. Not sure how great that network is, but Vodafone Italy was great, both 3G and LTE. I was even impressed how great the network was while traveling on the high speed trains (around 150 mph) between Rome and Florence, Florence and Venice, and Venice and Milan.

 

What unlocked mifi did you buy?

 

We borrowed a Huawei E5377T from a friend. Worked great, battery life lasted the whole day with 2 devices connected to it.

Link to comment
Share on other sites

Previously I mentioned not being able to use the Aquos phone wifi calling in Mexico. The problem was it wouldnt accept the address.

 

I was there this weekend and gave it another go.

 

Test 1: Tried the locate me feature, failed.

 

Test 2: Went to Google Maps, selected my location, selected the "whats here option" and copied over the entire address. Ie, house number, road, neighborhood, larger neighbhood, city, state, countyy, postal code. Said the address did not work.

 

Test 3: Disabled locate me, tried typing in a US address. As I was halfway through, the program would crash and it would say "unfortunately, settings has failed". Repeated 4 times.

 

Test 4: Tried a much simpler (but still real) US address. (ie, 123 Main Street, vs 2047 Marymount Lane). As I was typing it, the full address appeared as a suggestion. I selected it, and it was accepted!

 

So I was able to get wifi calling working on the Aquos in Mexico, no thanks to the garbage software.

 

However, texting and calling works great.

 

So my advice to anyone travelling abroad is to just use a simple US address.

Link to comment
Share on other sites

Previously I mentioned not being able to use the Aquos phone wifi calling in Mexico. The problem was it wouldnt accept the address.

 

I was there this weekend and gave it another go.

 

Test 1: Tried the locate me feature, failed.

 

Test 2: Went to Google Maps, selected my location, selected the "whats here option" and copied over the entire address. Ie, house number, road, neighborhood, larger neighbhood, city, state, countyy, postal code. Said the address did not work.

 

Test 3: Disabled locate me, tried typing in a US address. As I was halfway through, the program would crash and it would say "unfortunately, settings has failed". Repeated 4 times.

 

Test 4: Tried a much simpler (but still real) US address. (ie, 123 Main Street, vs 2047 Marymount Lane). As I was typing it, the full address appeared as a suggestion. I selected it, and it was accepted!

 

So I was able to get wifi calling working on the Aquos in Mexico, no thanks to the garbage software.

 

However, texting and calling works great.

 

So my advice to anyone travelling abroad is to just use a simple US address.

 

Odd, when I was in Italy last week it never asked for a USA address. I just got a pop-up warning that emergency services wouldn't be available since my WiFi access point was outside of the USA (see my post above, #212). Once I said ok, my WiFi calling/texting was connected. Worked like a charm. Wonder why your phone was asking for an address while in Mexico...

Link to comment
Share on other sites

Odd, when I was in Italy last week it never asked for a USA address. I just got a pop-up warning that emergency services wouldn't be available since my WiFi access point was outside of the USA (see my post above, #212). Once I said ok, my WiFi calling/texting was connected. Worked like a charm. Wonder why your phone was asking for an address while in Mexico...

 

My guess is it's an issue with the last software update on the Aquos. This isn't the first time we heard of WiFi calling messing up on that phone, just the first international problem. I believe Robert had similar issues with his Aquos.

  • Like 3
Link to comment
Share on other sites

Aquos WiFi calling = No bueno

 

Since the last update in December, WiFi calling address issues constantly plague me. Sharp has asked me to mail it to them for replacement or repair. I think I will send it in after my trip this weekend.

 

Using Nexus 6 on Tapatalk

Link to comment
Share on other sites

Yep, I'm pretty sure that it's just an issue with the Aquos as I've mentioned before.

 

Aquos WiFi calling = No bueno

 

Since the last update in December, WiFi calling address issues constantly plague me. Sharp has asked me to mail it to them for replacement or repair. I think I will send it in after my trip this weekend.

 

Using Nexus 6 on Tapatalk

 

Were you having the same problem, where the address screen would constantly crash? Or something else?

 

I didnt test it extensively, but at my dads house (USA lcoation), with the Aquos, I found better call quality using the Airave than with wifi calling, at the same distance from the transmission point.

 

The Airave sounded normal (not HD), but the Aquos would ocassionally break up.

 

I didnt have time to troubleshoot, so I simply turned off wifi calling and kept the Airave.

 

In Mexico I only made one short call to confirm it would work, so I didnt have time to experience if the call quality would also suffer.

Link to comment
Share on other sites

Anyone experiencing choppy incoming audio? I've had it more than a few times while at home. We use FIOS. It's impossible to have a conversation so I end up turning off wifi and calling the person back. It would be nice if it could hand off. It's also happened a few other places. Mostly public wifi.

Link to comment
Share on other sites

I find wifi calling overall to be a very poor experience on iPhone. I get better results on 1 bar of 1x. Even with 50/50 Fios with low pings, and wifi connect router, I get audio cut out and very low quality calls. Sometimes calls won't complete. And every so often they are perfect and I have no issues. Not sure what the problem is, but I'm keeping it off for now.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • large.unreadcontent.png.6ef00db54e758d06

  • Similar Content

  • Posts

    • Since this is kind of the general chat thread, I have to share this humorous story (at least it is to me): Since around February/March of this year, my S22U has been an absolute pain to charge. USB-C cables would immediately fall out and it progressively got worse and worse until it often took me a number of minutes to get the angle of the cable juuuussst right to get charging to occur at all (not exaggerating). The connection was so weak that even walking heavily could cause the cable to disconnect. I tried cleaning out the port with a stable, a paperclip, etc. Some dust/lint/dirt came out but the connection didn't improve one bit. Needless to say, this was a MONSTER headache and had me hating this phone. I just didn't have the finances right now for a replacement.  Which brings us to the night before last. I am angry as hell because I had spent five minutes trying to get this phone to charge and failed. I am looking in the port and I notice it doesn't look right. The walls look rough and, using a staple, the back and walls feel REALLY rough and very hard. I get some lint/dust out with the staple and it improves charging in the sense I can get it to charge but it doesn't remove any of the hard stuff. It's late and it's charging, so that's enough for now. I decide it's time to see if that hard stuff is part of the connector or not. More aggressive methods are needed! I work in a biochem lab and we have a lot of different sizes of disposable needles available. So, yesterday morning, while in the lab I grab a few different sizes of needles between 26AWG and 31 AWG. When I got home, I got to work and start probing the connector with the 26 AWG and 31 AWG needle. The stuff feels extremely hard, almost like it was part of the connector, but a bit does break off. Under examination of the bit, it's almost sandy with dust/lint embedded in it. It's not part of the connector but instead some sort of rock-hard crap! That's when I remember that I had done some rock hounding at the end of last year and in January. This involved lots of digging in very sandy/dusty soils; soils which bare more than a passing resemblance to the crap in the connector. We have our answer, this debris is basically compacted/cemented rock dust. Over time, moisture in the area combined with the compression from inserting the USB-C connector had turned it into cement. I start going nuts chiseling away at it with the 26 AWG needle. After about 5-10 minutes of constant chiseling and scraping with the 26AWG and 31AWG needles, I see the first signs of metal at the back of the connector. So it is metal around the outsides! Another 5 minutes of work and I have scraped away pretty much all of the crap in the connector. A few finishing passes with the 31AWG needle, a blast of compressed air, and it is time to see if this helped any. I plug my regular USB-C cable and holy crap it clicks into place; it hasn't done that since February! I pick up the phone and the cable has actually latched! The connector works pretty much like it did over a year ago, it's almost like having a brand new phone!
    • That's odd, they are usually almost lock step with TMO. I forgot to mention this also includes the September Security Update.
    • 417.55 MB September security update just downloaded here for S24+ unlocked   Edit:  after Sept security update install, checked and found a 13MB GP System update as well.  Still showing August 1st there however. 
    • T-Mobile is selling the rest of the 3.45GHz spectrum to Columbia Capital.  
    • Still nothing for my AT&T and Visible phones.
  • Recently Browsing

    • No registered users viewing this page.
×
×
  • Create New...