Jump to content

Everything 800mhz (1xA, LTE, coverage, timeline, etc)


Recommended Posts

How can I tell if my LTE EVO is picking up a 800 signal? I have the signalcheck lite app will this tell me?

 

Yes, signalcheck will show 1X800 in the 1X portion of the signal display. If you have the pro version, it will also notify you when it detects an 800SMR signal. 

  • Like 1
Link to comment
Share on other sites

How can I tell if my LTE EVO is picking up a 800 signal? I have the signalcheck lite app will this tell me?

 

In SignalCheck, apparently if the SID is 22xx, it's 800Mhz.  You don't need the Pro version to see the SID.

Edited by TyrellCorpse
Link to comment
Share on other sites

Received a notification today from signal check that my phone connected to 1x 800. It was weird because I have full bars on 1xrtt and when it connected to 800 it went down to one bar. I am guessing they were testing it or something. I thought 800 was supposed to boost your signal not make it worse. I am in Vancouver Washington and I am in a 4g area.

Link to comment
Share on other sites

It looks like there won't be any in San Diego for quite some time, not until they get approval to use the 800 Mhz frequencies for CDMA/LTE.

 

There is an 80 mile buffer zone where these aren't getting converted.

 

It's already been said, but an iDEN conversion doesn't refer to the spectrum being used, rather that the site, which was formerly an iDEN only site, is being converted to a Sprint NV site. These sites, if in the IBEZ, will broadcast PCS 3G and LTE, just like any other Sprint NV site in the IBEZ. 

Link to comment
Share on other sites

Received a notification today from signal check that my phone connected to 1x 800. It was weird because I have full bars on 1xrtt and when it connected to 800 it went down to one bar. I am guessing they were testing it or something. I thought 800 was supposed to boost your signal not make it worse. I am in Vancouver Washington and I am in a 4g area.

 

It sounds like the site that was broadcasting 800 was much further away than the site you were connected to previously. This is likely due to the fact that Android phones do actively scan for 800 (unlike iPhones) and will try to hold onto that 800 signal until it's gone. Once all the towers in the area are upgraded, it will boost your signal, this won't be a problem anymore.

  • Like 1
Link to comment
Share on other sites

Received a notification today from signal check that my phone connected to 1x 800. It was weird because I have full bars on 1xrtt and when it connected to 800 it went down to one bar. I am guessing they were testing it or something. I thought 800 was supposed to boost your signal not make it worse. I am in Vancouver Washington and I am in a 4g area.

The 800 signal might be coming from a more distant tower.

Link to comment
Share on other sites

In SignalCheck, apparently if the SID is 22xx, it's 800Mhz.  You don't need the Pro version to see the SID.

 

Nope.  The 1x800 SID's are 5 digits, 224xx if memory serves. ;)

Link to comment
Share on other sites

Are the iden cells just not accepting connections or is the carrier actually not on the air?

 

Sent from my SPH-L900 using Tapatalk 4 Beta

 

 

Link to comment
Share on other sites

Received a notification today from signal check that my phone connected to 1x 800. It was weird because I have full bars on 1xrtt and when it connected to 800 it went down to one bar. I am guessing they were testing it or something. I thought 800 was supposed to boost your signal not make it worse. I am in Vancouver Washington and I am in a 4g area.

As the others have said, this occurs when the 800 1x site you're connecting to is farther away than the 1900 1x site you were connected to. So that is the reduction in signal strength. When the closer 1900 site gets upgraded to 800, then you'd likely be impressed.

 

Robert from Note 2 using Tapatalk 4 Beta

 

 

  • Like 2
Link to comment
Share on other sites

Thanks for the feedback. Will look forward to it.

As the others have said, this occurs when the 800 1x site you're connecting to is farther away than the 1900 1x site you were connected to. So that is the reduction in signal strength. When the closer 1900 site gets upgraded to 800, then you'd likely be impressed.

 

Robert from Note 2 using Tapatalk 4 Beta

Edited by Olejkab
Link to comment
Share on other sites

It looks like there won't be any in San Diego for quite some time, not until they get approval to use the 800 Mhz frequencies for CDMA/LTE.

 

There is an 80 mile buffer zone where these aren't getting converted.

 

It's actually ~52 miles. The limit is 100km from the border. That being said, I've seen some scheduled Network Vision enhancements for 800MHz here on the southern edges of Tucson... that's within the IBEZ. I wouldn't give up all hope if you're within that boundary zone.

  • Like 1
Link to comment
Share on other sites

My first time connecting to an 800 tower in my area... Does everything look good and from reports in our Columbus market thread is backhaul isn't connected yet, will the 800 and 3g nv improve once completed?

 

Sent from my EVO using Tapatalk 4 Beta

uploadfromtaptalk1373032290913.jpg

uploadfromtaptalk1373032316490.jpg

  • Like 1
Link to comment
Share on other sites

My first time connecting to an 800 tower in my area... Does everything look good and from reports in our Columbus market thread is backhaul isn't connected yet, will the 800 and 3g nv improve once completed?

 

Sent from my EVO using Tapatalk 4 Beta

Looking at your 800 1X and EVDO signal level, I would suspect the 800 is coming from a site further away from you than your EVDO is.    Hard to really prove that, but normally the 800 will be better than EVDO if it is all coming from the some site.  If I am correct, you will see an upgrade at a closer site and see even better 800 signal level.

 

Upgraded backhaul will give you LTE and possibly improved speeds on EVDO especially if they have not been good.

It will not help your 800 1X until another site closer to you gets upgraded.  Your 800 level is surely good enough to work well, but I suspect it is going to get better based on your EVDO level.

  • Like 1
Link to comment
Share on other sites

I'm in Vegas for vacation and as soon as I landed and I've been picking up CDMA 1X 800. I'm on digiblurs custom PRL. My wife on a stock GS3 and stock PRL can't pick it up for some reason. I went ahead and updated PRL to stock and then couldn't pick it up. Reverted back to custom PRL and I've got it again.

 

Posted Image

 

Sent from my HTCONE using Tapatalk 4 Beta

 

 

  • Like 3
Link to comment
Share on other sites

You sound just like my experience where my wife's S3 was dead since EVDO was flooded.  I had 800SMR to play with for my data usage.  Except when I was there there weren't any LTE sites.

Link to comment
Share on other sites

You sound just like my experience where my wife's S3 was dead since EVDO was flooded. I had 800SMR to play with for my data usage. Except when I was there there weren't any LTE sites.

 

Yeah that's pretty much how it's been. EVDO has been useless for the most part.

 

Sent from my HTCONE using Tapatalk 4 Beta

 

 

Link to comment
Share on other sites

Is Sprint going to deploy a 3x3 MHz LTE carrier in markets of southeast US? I am curious when Sprint starts rolling out triband LTE devices if they will test 3 and 5 MHz bandwidths for 800 MHz.

 

Also I don't understand the new proposed 800 MHz Mexican/US band plan below. What does "Co-Primary" mean? Does this mean that if this new band plan passes those cities near the Mexican border will be able to deploy a 3x3 LTE carrier and 1 CDMA carrier?

 

BandPlan.jpg

Link to comment
Share on other sites

So in boston, and if I'm on the stock PRL i get 1xRTT, but when i flash the custom PRL i get 800mhz coverage (same spot)

 

Anyone know what's going on?  Does the stock PRL not prioritize 800mhz at all??

 

(custom PRL is out of date i think, it's 33010, whereas the stock is 25015)

Link to comment
Share on other sites

Is Sprint going to deploy a 3x3 MHz LTE carrier in markets of southeast US? I am curious when Sprint starts rolling out triband LTE devices if they will test 3 and 5 MHz bandwidths for 800 MHz.

 

Also I don't understand the new proposed 800 MHz Mexican/US band plan below. What does "Co-Primary" mean? Does this mean that if this new band plan passes those cities near the Mexican border will be able to deploy a 3x3 LTE carrier and 1 CDMA carrier?

 

Looks like at least one 5x5 LTE and 1 CDMA carrier, for a grand total of 12.5MHz (6.25 each direction).

Link to comment
Share on other sites

So in boston, and if I'm on the stock PRL i get 1xRTT, but when i flash the custom PRL i get 800mhz coverage (same spot)

 

Anyone know what's going on? Does the stock PRL not prioritize 800mhz at all??

 

(custom PRL is out of date i think, it's 33010, whereas the stock is 25015)

 

Actually the custom one is ahead of 25015...what SID are you seeing 800smr on?

Link to comment
Share on other sites

Looks like at least one 5x5 LTE and 1 CDMA carrier, for a grand total of 12.5MHz (6.25 each direction).

 

Would that mean San Diego can get LTE using 800Mhz?

Link to comment
Share on other sites

Actually the custom one is ahead of 25015...what SID are you seeing 800smr on?

25015 sid 1xrtt gives sid 4106 (-69dBm)

 

33010 on 800mhz gives sid 22429 (-71dBm)

 

so different towers

Link to comment
Share on other sites

Looks like at least one 5x5 LTE and 1 CDMA carrier, for a grand total of 12.5MHz (6.25 each direction).

 

What are you talking about?  The new 800 MHz band plan would only give Sprint 5.5 x 5.5 MHz to play with.  That means at most a 3x3 LTE carrier and a 1.25x1.25 CDMA carrier can be deployed at 800 MHz.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • large.unreadcontent.png.6ef00db54e758d06

  • gallery_1_23_9202.png

  • Similar Content

  • Posts

    • Since this is kind of the general chat thread, I have to share this humorous story (at least it is to me): Since around February/March of this year, my S22U has been an absolute pain to charge. USB-C cables would immediately fall out and it progressively got worse and worse until it often took me a number of minutes to get the angle of the cable juuuussst right to get charging to occur at all (not exaggerating). The connection was so weak that even walking heavily could cause the cable to disconnect. I tried cleaning out the port with a stable, a paperclip, etc. Some dust/lint/dirt came out but the connection didn't improve one bit. Needless to say, this was a MONSTER headache and had me hating this phone. I just didn't have the finances right now for a replacement.  Which brings us to the night before last. I am angry as hell because I had spent five minutes trying to get this phone to charge and failed. I am looking in the port and I notice it doesn't look right. The walls look rough and, using a staple, the back and walls feel REALLY rough and very hard. I get some lint/dust out with the staple and it improves charging in the sense I can get it to charge but it doesn't remove any of the hard stuff. It's late and it's charging, so that's enough for now. I decide it's time to see if that hard stuff is part of the connector or not. More aggressive methods are needed! I work in a biochem lab and we have a lot of different sizes of disposable needles available. So, yesterday morning, while in the lab I grab a few different sizes of needles between 26AWG and 31 AWG. When I got home, I got to work and start probing the connector with the 26 AWG and 31 AWG needle. The stuff feels extremely hard, almost like it was part of the connector, but a bit does break off. Under examination of the bit, it's almost sandy with dust/lint embedded in it. It's not part of the connector but instead some sort of rock-hard crap! That's when I remember that I had done some rock hounding at the end of last year and in January. This involved lots of digging in very sandy/dusty soils; soils which bare more than a passing resemblance to the crap in the connector. We have our answer, this debris is basically compacted/cemented rock dust. Over time, moisture in the area combined with the compression from inserting the USB-C connector had turned it into cement. I start going nuts chiseling away at it with the 26 AWG needle. After about 5-10 minutes of constant chiseling and scraping with the 26AWG and 31AWG needles, I see the first signs of metal at the back of the connector. So it is metal around the outsides! Another 5 minutes of work and I have scraped away pretty much all of the crap in the connector. A few finishing passes with the 31AWG needle, a blast of compressed air, and it is time to see if this helped any. I plug my regular USB-C cable and holy crap it clicks into place; it hasn't done that since February! I pick up the phone and the cable has actually latched! The connector works pretty much like it did over a year ago, it's almost like having a brand new phone!
    • That's odd, they are usually almost lock step with TMO. I forgot to mention this also includes the September Security Update.
    • 417.55 MB September security update just downloaded here for S24+ unlocked   Edit:  after Sept security update install, checked and found a 13MB GP System update as well.  Still showing August 1st there however. 
    • T-Mobile is selling the rest of the 3.45GHz spectrum to Columbia Capital.  
    • Still nothing for my AT&T and Visible phones.
  • Recently Browsing

    • No registered users viewing this page.
×
×
  • Create New...