Jump to content

Everything 800mhz (1xA, LTE, coverage, timeline, etc)


Recommended Posts

If I'm on 800 should I still get 1900 EVDO for data.

 

Maybe. That depends upon propagation. But CDMA1X and EV-DO are wholly separate, so one does not affect the other.

 

AJ

Link to comment
Share on other sites

 

Is it mostly the SF Bay market or are we seeing it in the South Bay too?

 

So far, just SF Bay. It will be all markets eventually.

 

Robert via Samsung Note II via Tapatalk

 

 

Link to comment
Share on other sites

If I'm on 800 should I still get 1900 EVDO for data.

 

I think I remember reading Sprint won't be using 800 for EVDO, just 1xadvance for voice and eventually LTE for data.

Link to comment
Share on other sites

 

I think I remember reading Sprint won't be using 800 for EVDO, just 1xadvance for voice and eventually LTE for data.

 

This is correct.

 

Robert via Nexus 4 using Tapatalk 2

 

 

Link to comment
Share on other sites

Regarding SFO and northern cali, is the 800 SMR hosting LTE too, or just voice? Is 800 LTE deployed anywhere?

 

800 LTE has not been deployed, and won't be until after Nextel is taken down. But yes, later this year, 800 SMR will be hosting CDMA 1x voice, and LTE.

Link to comment
Share on other sites

LTE on 800smr can't roll out until iden is shut down in June of this year.

 

Now of course they could test it out in areas where nextel isn't around for many miles. There are currently no handsets though.

 

Sent from my little Note2

 

 

Link to comment
Share on other sites

It appears that in Kansas, iDEN has been taken down from SMR. AJ can't find it in his spectrum sweeps. Just CDMA 800 has been located.

 

It's possible that iDEN has been shunted to 900MHz to finish its final days to euthanasia. If so, that would leave LTE 800 free space for some testing and then deployment.

 

Robert via Nexus 4 using Tapatalk 2

 

 

  • Like 5
Link to comment
Share on other sites

It appears that in Kansas, iDEN has been taken down from SMR. AJ can't find it in his spectrum sweeps. Just CDMA 800 has been located.

 

It's possible that iDEN has been shunted to 900MHz to finish its final days to euthanasia. If so, that would leave LTE 800 free space for some testing and then deployment.

 

Robert via Nexus 4 using Tapatalk 2

 

Is Kansas one of the SMR LTE FIT locations? We knew Montana and Louisiana, correct?

Link to comment
Share on other sites

 

Is Kansas one of the SMR LTE FIT locations? We knew Montana and Louisiana, correct?

 

I'm not aware of a Kansas LTE 800 FIT. In the docs I seen, it referenced "New Orleans and Montana LTE 800 FIT's". However, these docs were from Spring 2012.

 

The FIT plans could have changed since then. I've not heard a peep about LTE 800 FIT's since that time.

 

To clarify, AJ has only found what appears to be CDMA 800 in Kansas so far.

 

Robert via Nexus 4 using Tapatalk 2

 

 

  • Like 1
Link to comment
Share on other sites

I'm not aware of a Kansas LTE 800 FIT. In the docs I seen, it referenced "New Orleans and Montana LTE 800 FIT's". However, these docs were from Spring 2012.

 

The FIT plans could have changed since then. I've not heard a peep about LTE 800 FIT's since that time.

 

To clarify, AJ has only found what appears to be CDMA 800 in Kansas so far.

 

Robert via Nexus 4 using Tapatalk 2

 

I saw AJ's screen shot from Kansas, if that is 1xA, what would be different about an LTE carrier?

Link to comment
Share on other sites

 

I saw AJ's screen shot from Kansas, if that is 1xA, what would be different about an LTE carrier?

 

Location, location, location. Oh yeah, and carrier width.

 

Robert via Samsung Note II via Tapatalk

 

 

  • Like 1
Link to comment
Share on other sites

Location, location, location. Oh yeah, and carrier width.

 

Robert via Samsung Note II via Tapatalk

I have a Nextel/verizon/AT&T tower behind me. I know Verizon just upgraded that tower's 3G and 4G. I know there are 4 Of those triangles with the things on it. But there is only two now with the pads on them, the two in the middle are bear. And the one on top and one on bottom have s*** all over it lol
Link to comment
Share on other sites

I have a Nextel/verizon/AT&T tower behind me. I know Verizon just upgraded that tower's 3G and 4G. I know there are 4 Of those triangles with the things on it. But there is only two now with the pads on them, the two in the middle are bear. And the one on top and one on bottom have shit all over it lol

 

Not the first time I've heard Nextel and s*** used in the same sentence before.

 

Robert via Samsung Note II via Tapatalk

 

 

  • Like 4
Link to comment
Share on other sites

 

 

The 25xxx series has had 800smr for quite a while in two SIDs. Later Baltimore was added and now this one.

 

55xxx does not have a new one yet.

 

Sent from my little Note2

 

I just got 55012 yesterday. I remember having 55010 a couple days ago... I'm on your 800 PRL right now.

Link to comment
Share on other sites

It appears that in Kansas, iDEN has been taken down from SMR. AJ can't find it in his spectrum sweeps. Just CDMA 800 has been located.

 

It's possible that iDEN has been shunted to 900MHz to finish its final days to euthanasia. If so, that would leave LTE 800 free space for some testing and then deployment.

 

Robert via Nexus 4 using Tapatalk 2

LTE 800 FIT in Emporia would not hurt my feelings.
  • Like 1
Link to comment
Share on other sites

 

Basically if you look at the images of the numerous network vision panels posted around here, it's quite simple. The basic NV panel is 2 1900mhz on opposite sides while the 800mhz is squashed in the middle between the two. The 800mhz is not hooked up yet but everything is already there. All you need to do is go back to the towers and phsyically hook it up and do a few "magical" things and it's up and running. Should be much quicker than completely replacing all the old panels, dig up the T1 lines and get the fiber lines all set up, and replacing the old / outdated / inefficient hardware on sites. It's like 6 old boxes to 1 compact boxes.

 

In short, much easier/faster than the initial deployment.

 

I know this is an old post quoted here but it got me thinking...

 

If they leave the 800mhz antenna in each sector/panel unhooked and just plan on coming back to connect with a carrier card and get LTE800 up then..... Then how are ones getting 800 cdma 1xAdvanced currently?....

 

Whole reason I was thinking is I know there are 3 antennas in each sector panel one cdma 1900, one lte1900, and one 800... Question is if the 800mhz antenna is going to support both 1xadvance and lte, and if that's the case then why can't the 1900mhz antennae handle both cdma and lte signals at same time?... Jw bc I thought for 800 lte they'd have to add another panel and the current one initially installed would be hooked up to 1xadvance and just waiting on them to turn it on...

 

Sent from my EVO using Tapatalk 2

 

 

Link to comment
Share on other sites

 

 

I know this is an old post quoted here but it got me thinking...

 

If they leave the 800mhz antenna in each sector/panel unhooked and just plan on coming back to connect with a carrier card and get LTE800 up then..... Then how are ones getting 800 cdma 1xAdvanced currently?....

 

Whole reason I was thinking is I know there are 3 antennas in each sector panel one cdma 1900, one lte1900, and one 800... Question is if the 800mhz antenna is going to support both 1xadvance and lte, and if that's the case then why can't the 1900mhz antennae handle both cdma and lte signals at same time?... Jw bc I thought for 800 lte they'd have to add another panel and the current one initially installed would be hooked up to 1xadvance and just waiting on them to turn it on...

 

Sent from my EVO using Tapatalk 2

My guess is that you can only do two things on one antenna like 1x/lte or 1x/evdo not all three that's just a guess

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • large.unreadcontent.png.6ef00db54e758d06

  • Similar Content

  • Posts

    • Since this is kind of the general chat thread, I have to share this humorous story (at least it is to me): Since around February/March of this year, my S22U has been an absolute pain to charge. USB-C cables would immediately fall out and it progressively got worse and worse until it often took me a number of minutes to get the angle of the cable juuuussst right to get charging to occur at all (not exaggerating). The connection was so weak that even walking heavily could cause the cable to disconnect. I tried cleaning out the port with a stable, a paperclip, etc. Some dust/lint/dirt came out but the connection didn't improve one bit. Needless to say, this was a MONSTER headache and had me hating this phone. I just didn't have the finances right now for a replacement.  Which brings us to the night before last. I am angry as hell because I had spent five minutes trying to get this phone to charge and failed. I am looking in the port and I notice it doesn't look right. The walls look rough and, using a staple, the back and walls feel REALLY rough and very hard. I get some lint/dust out with the staple and it improves charging in the sense I can get it to charge but it doesn't remove any of the hard stuff. It's late and it's charging, so that's enough for now. I decide it's time to see if that hard stuff is part of the connector or not. More aggressive methods are needed! I work in a biochem lab and we have a lot of different sizes of disposable needles available. So, yesterday morning, while in the lab I grab a few different sizes of needles between 26AWG and 31 AWG. When I got home, I got to work and start probing the connector with the 26 AWG and 31 AWG needle. The stuff feels extremely hard, almost like it was part of the connector, but a bit does break off. Under examination of the bit, it's almost sandy with dust/lint embedded in it. It's not part of the connector but instead some sort of rock-hard crap! That's when I remember that I had done some rock hounding at the end of last year and in January. This involved lots of digging in very sandy/dusty soils; soils which bare more than a passing resemblance to the crap in the connector. We have our answer, this debris is basically compacted/cemented rock dust. Over time, moisture in the area combined with the compression from inserting the USB-C connector had turned it into cement. I start going nuts chiseling away at it with the 26 AWG needle. After about 5-10 minutes of constant chiseling and scraping with the 26AWG and 31AWG needles, I see the first signs of metal at the back of the connector. So it is metal around the outsides! Another 5 minutes of work and I have scraped away pretty much all of the crap in the connector. A few finishing passes with the 31AWG needle, a blast of compressed air, and it is time to see if this helped any. I plug my regular USB-C cable and holy crap it clicks into place; it hasn't done that since February! I pick up the phone and the cable has actually latched! The connector works pretty much like it did over a year ago, it's almost like having a brand new phone!
    • That's odd, they are usually almost lock step with TMO. I forgot to mention this also includes the September Security Update.
    • 417.55 MB September security update just downloaded here for S24+ unlocked   Edit:  after Sept security update install, checked and found a 13MB GP System update as well.  Still showing August 1st there however. 
    • T-Mobile is selling the rest of the 3.45GHz spectrum to Columbia Capital.  
    • Still nothing for my AT&T and Visible phones.
  • Recently Browsing

    • No registered users viewing this page.
×
×
  • Create New...